ADTRAN 239 HR Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 14

ADTRAN 239 HR Скачать руководство пользователя страница 8

A-1

Section 61246045L1-5, Issue 2

61246045L1-5B

This Appendix describes the use and operation of
loopback control code sequences used in
ADTRAN’s HDSL system.

Loopback control codes are governed by the HTU-C
(and HRE(s) if deployed). Two types of HTU-Cs
exist which enable two different sets of loopback
codes: Standard or Enhanced loopbacks. The
Standard loopbacks are those that have been
contained in ADTRAN’s HDSL product family
beginning with 2

nd

Generation products. The

Enhanced loopbacks are contained in selected
ADTRAN HTU-C units. The following table
denotes whether the HTU-C (part number) contains
Standard or Enhanced loopback capabilities.

Standard Loopback

Part Number

Description

1242002Lx ............. 220/E220 HTU-C
1242016L1 ............. 3192 HTU-C
1242023L1 ............. DDM+ HTU-C
1244001L1 ............. E220/220 Low Voltage

T1 HTU-C

1244002L1 - L3 ..... Litespan AHDSL
1244002L4 - L6 ..... Litespan AHT1U
1245001L1-L2 ....... E220/220 Low Voltage

5

th

Gen HTU-C

1245003L1-L2 ....... DDM+ 5

th

Gen HTU-C

1245004L1-L2 ....... 3192 5

th

Gen HTU-C

Enhanced Loopback

Part Number

Description

1245001L4-L8 ....... E220/220 HTU-C
1245002L6 ............. Litespan AHT1U
1245003L4-L8 ....... DDM+ HTU-C
1245004L4-L8 ....... 3192 HTU-C
1246001L4-L8........E220/220 HTU-C

1246003L4-L8........DDM+HTU-C
1246004L4-L8........3192 HTU-C

The HREs and HTU-Rs’ loopback capabilities are
controlled from the central office unit (HTU-C).

NOTE:

If the HTU-C on a circuit contains Standard
loopbacks, then refer to subsection 1 of this
Appendix to determine its capabilities. If
the HTU-C on a circuit contains Enhanced
loopbacks, then refer to subsection 2 of this
Appendix to determine its loopback
capabilities.

A-1. STANDARD LOOPBACKS

This subsection describes operation of the HDSL
system in detection of in-band and ESF facility data
link loopback codes. The operation of the loopback
commands in the ADTRAN HDSL system is
compliant with the recommendation to ANSI
recorded in T1E1.4/92. The HDSL network
loopback points described below are shown in

Figures A-1 and A-2

.

HTU-C loopback is a regenerative loopback of the
DSX-1 signal toward the network.

HTU-R loopback is a regenerative loopback of the
DS1 signal toward the network. This loopback is in
addition to a separate Smartjack loopback. Separate
activation sequences are provided for the HTU-R
and the Smartjack loopback initiation. The HDSL
loopbacks are implemented such that the
downstream HDSL elements (toward the customer)
remain synchronized.

Figure A-1. HDSL Loopback Points

HTU-C

HTU-R

NIU

HRE #1

DSX-1

Interface

HDSL
Loops

HDSL
Loops

DS1
Interface

HRE #2

Appendix A

HDSL Loopbacks

«
...
6
7
8
9
10
...
»

Содержание 239 HR















Отзывы:

Нет отзывов