220/DDM+/3192 H2TU-C
Option Settings Display (“VIEW”)
Message
Description
Settings
Default
LBO
Line Build Out
EXT, 0, 133, 266, 399, 533
*
CODE
Line Code
AMI, B8ZS
B8ZS
FRMG
DSX-1 Framing
AUTO, UNF
UNF
NLBK
NIU Loopback
EN, DIS
EN
LBTO
Loopback Timeout
NONE, 1 Hr, 2 Hr, 8 Hr, 24 Hr
1 Hr
CLOS
Customer Loss Response
AIS, LPBK
AIS
PRM
Performance Reporting Messages
NPRM, SPRM, NONE, AUTO
AUTO
TXLV
DS1 Transmit Level
0 dB, -7.5 dB, -15 dB
0 dB
SPWR
Span Power
EN, DIS
EN
ALMP
Alarm Pattern to Customer
AIS, LOS
AIS
* 220 = EXT, 3192/DDM+ = 0
Loopback Options Display (“LPBK”)
Select
Loopback State
Loopback Description
HTUC
NET
Network loopback at H2TU-C
CST
Customer loopback at H2TU-C
NONE
No active loopback
HTUR
BLB
Bidirectional loopback at H2TU-R
NET
Network loopback at H2TU-R
CST
Customer loopback at H2TU-R
NONE
No active loopback
DSX-1 BANTAM JACKS
EQ
■
Provides an intrusive access point to the data stream.
TX - Access the data stream being received from the network.
RX - Access the data stream being transmitted to the network.
MON
■
Provides a non-intrusive access point to the data stream.
TX - Monitors the data stream being received from the network
RX - Monitors the data stream being transmitted to the network.
NOTE:
The DDM+ H2TU-C does not have the DSX-1 Bantam Jacks option.
RS-232 DB-9 CONNECTOR
■
Used to access performance monitoring data, perform loopbacks and provision units via VT100
emulation applications such as Hyper Terminal – Private Edition, ProComm Plus, and Telnet.
■
There are two types of terminal emulation modes, Manual and Real-Time. Use “CTRL-T” to toggle
between the two modes.
Manual Emulation Mode
:
Press the space bar 3 times to manually update the screen. Print screen
and log file commands are available in this mode.
Real-Time Emulation Mode
:
The default mode. Print screen and log file commands are not
available in this mode. Cursor placement and screen highlighting are enabled.
■
Provision terminal port as follows:
Data Rate
— 1.2 to 19.2 kbps
Asynchronous Data Format
— eight data bits, no parity (none), one stop bit
■
When using a PC with terminal software, be sure to disable any power saving programs.
PROVISIONING NOTES
■
This unit can be provisioned via the RS-232 port or remotely via ITS codes. This unit cannot be
provisioned from the faceplate four-character display. Select “2” from the ADTRAN HDSL2 Main
Menu Screen to view the Provisioning Screen.
STATUS LED
STATUS
●
GREEN
Everything functioning normally
✷
BLINKING ES, SES, or BPV detected
●
YELLOW
Loopbacks active
✷
BLINKING In-band loopbacks armed
●
RED
Alarm on the HDSL2 loop, DSX or DS1 interface
✷
BLINKING Signal Quality of 0 or No Sync on the HDSL2 loop
FOUR-CHARACTER DISPLAY (FCD) OPERATION
FCD Modes
Mode
Message
Function
Status
STAT
Displays loop margin, alarms, and general status conditions
Display Off
Blank
Blank after five minutes of no activity
View
VIEW
View current options settings
Loopback
LPBK
Select and execute HDSL2 circuit loopbacks
Status/Alarm Display (“STAT”)
Message
Description
MARG xx
HDSL2 loop margin, 0-20
DSL ERR
CRC error detected on HDSL2 Loop
LOC ERR
Frame bit error (SF Mode), Bipolar Violation (BPV), or CRC error (ESF Mode)
detected locally at DSX-1 of the H2TU-C
REM ERR
Frame bit error (SF Mode), Bipolar Violation (BPV), or CRC error (ESF Mode)
detected remotely at DS1 of the H2TU-R
DSL LOS
No synchronization of H2TU-C and H2TU-R on loop
LOC LOS
DSX signal is absent from the network interface or is of a format which does
not match the provisioning of the HDSL2 circuit
REM LOS
DS1 signal is absent from the network interface or is of a format which does
not match the provisioning of the HDSL2 circuit
ARM
NIU Loopback is armed
Left = MODE
Center = OFF
Right = SELECT
1221001L6
STATUS
D
S
L
dB
SEL
MODE
R
S
2
3
2
E
Q
HIS
TX
RX
M
O
N
TX
D
S
X
RX
C A U T I O N
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
COMPLIANCE CODES
This product is intended for installation in restricted access locations only and in equip-
ment with a Type “B” or “E” installation code.
Input current at maximum load is 0.7 A at
–48 Vdc. Maximum output at over current
condition is 165 mA at –190 Vdc.
WARRANTY
Warranty for Carrier Networks products manufactured by ADTRAN and supplied under
Buyer’s order for use in the U.S. is ten (10) years. For a complete copy of ADTRAN’s U.S.
Carrier Networks Equipment Warranty: (877) 457-5007, Document #414.
CODE
IN
OUT
Installation Code (IC)
A
–
Telecommunication Code (TC)
–
X
Power Code (PC)
F
C
Reference Guide
61221001L6A-30B
0011
