job
Aid
D
ESCRIPTION
The
Small
Form
‐
Factor
Pluggable
OC
‐
12
80
km
Long
Reach
‐
2
(SFP
LR
‐
2)
plugs
into
ADTRAN
equipment
designed
to
accept
Small
Form
‐
factor
Pluggables
(SFPs).
Installed
into
an
appro
‐
priate
host
unit,
the
SFP
LR
‐
2
provides
an
OC
‐
12
interface
to
the
supporting
system.
NOTE
To
ensure
compatibility,
refer
to
the
documentation
provided
with
the
host
module.
The
following
features
are
supported
on
the
SFP
LR
‐
2:
♦
SONET
OC
‐
12
compatible
(622
Mb/s),
1550
nm
long
reach,
single
mode,
2
‐
fiber
operation
♦
80
km
maximum
optical
span
CAUTION
!
Due
to
compliance
certification
requirements,
only
SFPs
supplied
by
ADTRAN
are
to
be
used
with
the
host
module.
ADTRAN
cannot
certify
system
integrity
with
other
SFPs.
S
PECIFICATIONS
♦
Optical
Specifications:
◊
Transmit
power:
–3
dBm
to
+2
dBm
◊
Receive
power:
–28
dBm
to
–8
dBm
◊
Transmit
Wavelength:
1550
nm
◊
Optical
budget:
24
dB
◊
Optical
connectors:
LC
Small Form-Factor Pluggable OC-12
80 km Long Reach-2
♦
Extended
Environmental
Support:
◊
Operational
temperature
range:
–40°C
to
+65°C
◊
Storage
temperature
range:
–40°C
to
+85°C
◊
Relative
humidity
to
95%,
noncondensing
I
NSTALLATION
To
install
the
SFP
LR
‐
2
into
an
appropriate
module,
complete
the
following
steps:
1. Inspect
the
SFP
LR
‐
2.
If
damaged,
file
a
claim
with
the
car
‐
rier
and
then
contact
ADTRAN
Customer
Support.
CAUTION
!
Do
not
remove
the
protective
end
cap
from
the
SFP
until
the
fiber
optic
cable
is
ready
to
be
connected.
2. Insert
the
SFP
LR
‐
2
into
the
SFP
cage
on
the
module.
Ensure
that
the
manufacturer’s
label
on
the
SFP
is
facing
upward
for
correct
installation.
3. Slide
the
SFP
LR
‐
2
all
the
way
into
the
receptacle
until
there
is
an
audible
“click”.
NOTE
The
latch
on
the
SFP
is
used
to
remove
the
SFP
from
the
cage
on
the
circuit
card.
S
AFETY
AND
R
EGULATORY
C
OMPLIANCE
CAUTION
!
Electrostatic
Discharge
(ESD)
can
damage
electronic
modules.
When
handling
modules,
wear
an
antistatic
discharge
wrist
strap
to
prevent
damage
to
electronic
components.
Place
modules
in
antistatic
packing
material
when
transporting
or
storing.
When
working
on
modules,
always
place
them
on
an
approved
antistatic
mat
that
is
electrically
grounded.
The
SFP
meets
or
exceeds
all
the
applicable
requirements
of
NEBS,
Telcordia
GR
‐
63
‐
CORE,
GR
‐
1089
‐
CORE,
and
ETSI
EN
300368.
The
SFP
LR
‐
2
is
intended
for
deployment
in
Central
Office
type
facilities,
EEEs,
EECs,
and
locations
where
the
NEC
applies
(for
example,
Customer
Premises).
The
SFP
is
to
be
installed
in
ADTRAN
products
in
Restricted
Access
Locations
only,
and
installed
by
trained
service
personnel.
This
device
complies
with
Part
15
of
the
FCC
rules.
Operation
is
subject
to
the
following
two
conditions:
1. This
device
may
not
cause
harmful
interference
2. This
device
must
accept
any
interference
received,
including
interference
that
may
cause
undesired
operation.
CLEI: SOOTAE6J__
Product P/N: 1184544P5
Issue Date: November 2010
Document P/N: 61184544P5-22C
