ADLINK Technology STC2-10WP-AL Скачать руководство пользователя страница 109

Страница: 109 / 121

STC2-AL/KL Series

6 Driver & Application Installation

After installing the operating system, all related drivers must be

installed for the system to function properly. This section describes

the drivers needed for Windows operating systems and the proce

dures to install them. For other operating system support, contact

ADLINK for further information.
Visit the ADLINK web site to download drivers.

6.1 Driver Installation Order

Install drivers in the following order.

1. Fully install Microsoft Windows before installing any driv

ers. Most standard I/O device drivers have been

included in Microsoft Windows. For Windows 10 IoT

Enterprise users, Administrator privilege is required to

install the drivers.

2. Install the chipset driver.

See “Chipset Driver Installation” on page 100.

3. Install the graphics driver.

See “Graphics Driver Installation” on page 101.

4. Install the Ethernet driver.

See “Ethernet Driver Installation” on page 102.

5. Install the Management Engine driver

See “Management Engine Driver Installation” on

page 102.

6. Install the Serial I/O driver.

See “Serial I/O Driver Installation” on page 103.

7. DI/O Driver Installation

See “DI/O Driver Installation” on page 103.

Содержание STC2-10WP-AL


























































































































Результаты поиска

Содержание STC2-10WP-AL

Отзывы:

ADLINK Technology STC2-10WP-AL, Руководство пользователя, Страница: 109 / 121

Результаты поиска

Содержание STC2-10WP-AL

Отзывы: