ADLINK Technology ReadyBoard 910 Скачать руководство пользователя страница 56

Страница: 56 / 64

Chapter 4

BIOS Setup

Reference Manual

ReadyBoard 910

BIOS Save & Exit Setup Screen

Figure 4-6. BIOS Save & Exit Setup Screen

♦

Save Changes and Exit

•

Save configuration and exit? [

Yes

; No]

♦

Discard Changes and Exit

•

Quit without saving? [

Yes

; No]

♦

Save Changes and Reset

•

Save configuration and reset? [

Yes

; No]

♦

Discard Changes and Reset

•

Reset without saving? [

Yes

; No]

•

Save Options

♦

Save Changes

•

Save configuration [

Yes

; No]

♦

Discard Changes

•

Load Previous Values [

Yes

; No]

♦

Restore Defaults

•

Load Optimized Defaults [

Yes

; No]

Version X.XX.XXXX. Copyright (C) 20XX American Megatrends, Inc.

RB910_BIOS_Save&Exit_a

Main Advanced Chipset Boot Security Save & Exit

Save Changes and Exit

Save Changes and Reset

Discard Changes and Exit

Discard Changes and Reset

Save Options

Boot Override

Save Changes

Discard Changes

Save as User Defaults

Restore User Defaults

Restore Defaults

SATA: XXXXXXXXXXX

Launch EFI Shell from filesystem device

[Setting Description]

: Select Screen

: Select Item

+/- : Change field

F1 : General Help

Enter : Select

F2 : Previous Values

F3&F9 : Optimized Defaults

F4 : Save & Exit

F10 : Save & Reset

ESC: Exit

Содержание ReadyBoard 910

































































Результаты поиска

Содержание ReadyBoard 910

Отзывы:

Бренды по названию

Популярные бренды

ADLINK Technology ReadyBoard 910, Справочное руководство

Результаты поиска

Содержание ReadyBoard 910

Отзывы:

Бренды по названию

Популярные бренды