ADLINK Technology Express-KL Скачать руководство пользователя | Manualshive

Страница: 41 / 94

background image

Express-KL

Connector Pinouts on Module

35

4.6.2.

BIOS Select and Mode Configuration Switch

The module has two BIOS chips and BIOS operation can be configured to "PICMG" and dual-BIOS "Failsafe"
modes using BIOS Select and Mode Configuration Switch (also referred to as the Failsafe BIOS switch), Pin 2.

Setting the module to PICMG mode will configure the BIOS chips on the module as SPI0 and SPI1. In PICMG
mode, a BIOS chip cannot be placed in the SPI0 slot on the carrier.

In dual-BIOS Failsafe mode, both BIOS chips on the module are configured as SPI1. Only one of the two is
connected to the SPI bus at any given time. In case of failure of the primary SPI1 BIOS, the system will reboot and
switch to the secondary SPI1 BIOS on the module. In Failsafe mode, the SPI0 BIOS socket on the carrier can be
populated.

In either mode, BIOS Select and Mode Configuration Switch Pin 1 is used to select whether to boot from SPI0 or
SPI1.

Mode

Pin 1

Pin 2

Boot from SPI0 (default)

On

—

Boot from SPI1

Off

—

Set BIOS to PICMG mode

—

On

Set BIOS to Failsafe BIOS mode (default)

—

Off

Table 6: BIOS Select and Mode Configuration Switch Settings

«
...
39
40
41
42
43
...
»

Содержание Express-KL































































































Отзывы:

Нет отзывов

Похожие инструкции для Express-KL

Express5800/E120d-M

Бренд: NEC Страницы: 2

Бренд: Acconeer Страницы: 32

Бренд: Quatech Страницы: 27

Бренд: SAF Страницы: 30

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

Бренд: ZALMAN Страницы: 22

Бренд: Avolites Страницы: 24

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

REJ06B0734-0100

Бренд: Renesas Страницы: 19

Бренд: Commell Страницы: 36

EK-Quantum Vector FTW3 RTX 2080 Ti

Бренд: ekwb Страницы: 3

Бренд: Datavideo Страницы: 71

Бренд: Thecus Страницы: 90

Бренд: Valcom Страницы: 4

DAQ X NI 634 Series

Бренд: National Instruments Страницы: 278

Бренд: Lava Страницы: 1

NetLinx Master-Ethernet Card/Module NXC-ME260

Бренд: AMX Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды