ADLINK Technology Express-KL Скачать руководство пользователя

Страница: 11 / 94

Express-KL

Specifications

2.7. Serial I/O on Module

Chipset:

Nuvoton NCT5104D

Ports:

2x UARTs Rx/Tx only

Console Redirection:

COM 1 or COM 2 selectable in BIOS

COM Port Description

IRQ

Address

Console redirection support

COM 1

Supported by module (SER0, A98/A99), via NCT5104D

0x240

Yes

COM 2

Supported by module (SER1, A101/A102), via NCT5104D 11

0x248

Yes

COM 3

Supported by Super I/O (W83627DHG) on carrier board

0x3F8

Yes

COM 4

Supported by Super I/O (W83627DHG) on carrier board

0x2F8

Yes

2.8. Trusted Platform Module (TPM)

Chipset:

Infineon

SLB 9665XT2.0 FW5.51

Type:

TPM 2.0 (TPM 1.2 by BOM option, support by project basis)

2.9. SEMA Board Controller

Type:

ADLINK Smart Embedded Management Agent (SEMA)

Functions:

•

Voltage/Current

monitoring

•

Power sequence debug support

•

AT/ATX mode control

•

Logistics and forensic information

•

Flat panel control

•

General purpose I2C

•

Failsafe BIOS (dual BIOS )

•

Watchdog timer and fan control

2.10. Debug

40-pin flat cable connector to be used with DB-40 debug module

Supports: BIOS POST code LED, BMC access, SPI BIOS flashing, power testpoints, debug LEDs

60-pin XDP header for ICE debug of CPU/chipset

Содержание Express-KL































































































Результаты поиска

Содержание Express-KL

Отзывы:

Похожие инструкции для Express-KL

Бренды по названию

Популярные бренды

ADLINK Technology Express-KL, Руководство пользователя

Результаты поиска

Содержание Express-KL

Отзывы:

Похожие инструкции для Express-KL

Бренды по названию

Популярные бренды