ADLINK Technology cPCI-6630 Series Скачать руководство пользователя страница 50

Страница: 50 / 139

Board Interfaces

Leading

EDGE COMPUTING

4.7

Switches and Buttons

Refer to Section 4.1 cPCI-6630(D) Component Side Layout on
page 19 and Section 4.2 cPCI-6630 Solder Side Layout on
page 20 for switch and button locations.

System Reset Button (SW1)

The cPCI-6630(D) has a system reset button on the front panel.
Press the switch SW1 to reset the system.

Clear CMOS, RTC Reset Button (SW5)

Press switch SW5 to clear CMOS and reset the RTC.

COM1/2 Mode Switches (SW7/3)

Switch SW7 sets the mode of the COM1 port on the front panel.
Switch SW3 sets the mode of the COM2 port on layer 2 of the front
panel (cPCI-6630D only).

Mode

RS-232 (default)

OFF

RS-422

RS-485

OFF

1 2

Содержание cPCI-6630 Series












































































































































Результаты поиска

Содержание cPCI-6630 Series

Отзывы:

Похожие инструкции для cPCI-6630 Series

Бренды по названию

Популярные бренды

ADLINK Technology cPCI-6630 Series, Руководство пользователя

Результаты поиска

Содержание cPCI-6630 Series

Отзывы:

Похожие инструкции для cPCI-6630 Series

Бренды по названию

Популярные бренды