ADIATEK ruby 45 light, Использование и обслуживание

Страница: 22 / 52

GB GB
4. Clean the suction filter.
5. Replace the rubbers if worn out.
6. Check that the suction motor switch is on.
7. Check that the recovery tank is empty.
EXCESSIVE FOAM PRODUCTION
Check that low foam detergent has been used. Even-
tually add small quantities of anti foam liquid into
the recovery tank.
Please be aware that a bigger quantity of foam is
produced when the floor is not very dirty. In this ca-
se please dilute detergent solution.
PROGRAMMED MAINTENANCE
INTERVENTION DAILY WEEKLY TWO-MONTHLY SIX-MONTHLY
RECOVERY TANK CLEANING
•
SUCTION FILTER CLEANING
•
SOLUTION TANK FILTER CLEANING
•
BRUSHES CLEANING
•
BRUSHES DISASSEMBLY
•
SQUEEGEE CLEANING
•
FRONT SQUEEGEE RUBBER REPLACEMENT
•
REAR SQUEEGEE RUBBER REPLACEMENT
•
SPLASH GUARD RUBBER REPLACEMENT
•
SQUEEGEE ADJUSTMENT CHECK
•
SQUEEGEE HOSE CLEANING
•
SOLUTION TANK CLEANING
•
BATTERIES ELECTROLYTE CHECK
•
BRUSHES MOTOR CHECK
•
SUCTION MOTOR CHECK
•
BRUSHES BASE GROUP CHECK
•
SCREW TIGHTENING
•
RECOMMENDED BRUSHES
Brushes must be chosen depending on type of floor and dirt to be removed.
The employed material and the bristles diameter are the elements that distinguish different types of brushes.
MATERIAL CHARACTERISTICS
PPL (Polypropylene) Good wear resistance. Maintains characteristics with hot water up to 50°C. It is not hygroscopic.
NYLON Excellent wear resistance, even with hot water. It is hygroscopic.
TYNEX Nylon bristles with grains of abrasive material. Use with caution in order not to mark the floor or ruin the polishing.
BRISTLES THICKNESS Thicker bristles are more rigid and must be used on smooth floor or floor with small joints.
On irregular floors with deep joints or relieves, it is recommended to use softer bristles which penetrate more easily and deeper.
Please be aware that when brushes bristles are worn out and therefore too small, they become rigid and unable to penetrate and
clean deeper. This may also happen with thicker bristles creating brush vibration.
PAD HOLDER Pad holder is recommended to clean smooth surfaces. It has anchor points which permit the blocking of the abrasive pad during
work.
MACHINE CODE QUANTITY DESCRIPTION USE
ruby 45 light
48901010 2 Brush PPL 0,3 Ø 235 Irregular floors with large joints.
48901040 2 Brush NYLON 0,5 Ø 235 Smooth floors with small joints and persistent dirt.
48901050 2 Brush PPL 0,6 Ø 235 Smooth floors with small joints and persistent dirt.
48901060 2 Brush TYNEX Ø 235 Floors of resistant material and particularly dirty.
48901070 2 Brush 5 mix Ø 235 For all types of floors.
48801010 2 Pad holder Ø 230 For pads of 9”, for smooth surfaces cleaning.
ruby 55 light
48901110 2 Brush PPL 0,3 Ø 285 Irregular floors with large joints.
48901140 2 Brush NYLON 0,5 Ø 285 Smooth floors with small joints and persistent dirt.
48901150 2 Brush PPL 0,6 Ø 285 Smooth floors with small joints and persistent dirt.
48901160 2 Brush TYNEX Ø 285 Floors of resistant material and particularly dirty.
48901170 2 Brush PPL 0,9 Ø 285 Smooth floors with small joints and persistent dirt.
48901180 2 Brush 5-mix Ø 285 For all types of floors.
48801020 2 Pad holder Ø 280 For pads of 11”, for smooth surfaces cleaning.
22