manualshive.com logo in svg

Adeunis RF COMFORT MQTT, Руководство пользователя

Поделиться
Скачать
Adeunis RF COMFORT MQTT Скачать руководство пользователя страница 37

User Guide | COMFORT SERENITY MQTT | NB-IoT / LTE-Cat-M1

37

ATTENTION

If the manually selected network is not accessible (not supported by the SIM card 
or no network coverage), then the product will not be attached to any network.

4.6.2 Monitoring Network Attachment Status

At any time, the user can check the network connection status on the NFC IoT 
Configurator app.

📱

Go to the "DETAILS" menu of the sensor => Select the "DIAGNOSTIC"
section => Monitor the network attachment status using the "Network 
Connection Status" parameter..

Network attachment status

Description

Connected

Product in PARK mode or no network at the
installation location

Disconnected (timeout)

Network attachment time exceeds the
configured timeout in the product (default 120
seconds)

Searching

Product searching for a network connection

Connected

Product connected to the network

Содержание COMFORT MQTT
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды