Additel 226 Скачать руководство пользователя страница 43

Страница: 43 / 107

Table 10 Pressure measurement settings

Subject

Valid Value

Description

Resolution

4/5/6

Resolution of current measurement channel

Pressure type

Gauge/absolute

Current measurement channel pressure type

Measurement

frequency*

1~10Hz

Data acquisition frequency of the current measurement channel

Stability enable

Enable/disable

Whether to turn on the stability judgment function

Stability value

0.003-1

A value for judging whether the pressure is stable. If the measured value fluctuates

less than this value within the stable time, the calibrator will judge as stable

Stabilization time

1-60

Time to judge the pressure stability

Tare enable

Enable/disable

Enable or disable tare function

Tare value

（

-9999999~9999999

）

Correction value of the tare function

Tare units

Pressure units

All pressure units

*Note: Only available for some of the external pressure module.

3.2.2 Filter

See paragraph 3.1.8.

3.2.3 Module information

The pressure measurement provides function of view the information of external pressure module, click icon

the pressure measurement channel, and select module information in the pop-up menu to view the information.

Содержание 226












































































































Результаты поиска

Содержание 226

Отзывы:

Бренды по названию

Популярные бренды

Additel 226, Руководство пользователя

Результаты поиска

Содержание 226

Отзывы:

Бренды по названию

Популярные бренды