Additel 226 Скачать руководство пользователя страница 42

Страница: 42 / 107

3.1.9 Zeroing

The device provides short circuit zeroing function for current/ voltage signal, so as to eliminate the zero drift,

supported zeroing range is 1% FS.

3.1.10 Statistics

Click icon

in the channel, and select the statistics in the pop-up menu. Then there will be Max, Min and Avg

below the channel 1, click icon

to reset the statistics data.

3.2 Pressure measurement

The pressure measurement function is only available when an external pressure module is connected. This calibrator

provides two external module Lemo type connections A and B. When a pressure module is connected to connection A or

B, user needs to select on for measurement. Click the pressure unit above the pressure measurement value to switch the

pressure unit in the pop-up unit selection interface.

3.2.1 Pressure measurement settings

Click the menu button

in the pressure measurement channel and click the "Settings" menu in the pop-up menu

to set the pressure type, resolution, stability, tare and other functions of the current pressure measurement channel, see

Table 10.

Number of samples

1~100

Only available when the moving average filter is selected

De-extremum pairs

0~10

Only available when the moving average filter is selected

Содержание 226












































































































Результаты поиска

Содержание 226

Отзывы:

Бренды по названию

Популярные бренды

Additel 226, Руководство пользователя

Результаты поиска

Содержание 226

Отзывы:

Бренды по названию

Популярные бренды