ADC ECOWASH-MP2, Руководство пользователя и по обслуживанию, Страница: 26 / 34

26 113688- 1
CREATE CYCLE NAME
Cycle:
Wash 75°
Save cycle name?
COPY CYCLE NAME
Cycle:
Pre-wash
Save cycle name?
CHANGE CYCLE NAME
Cycle:
Soaking
Use the INC (
∧∧∧∧∧
) and DEC (
∨∨∨∨∨
) keys to modify the
character indicated by the cursor; use the ADVANCE
(>>) key to move the cursor to the next character. Once
the name has been written, press ENTER.
ENTER: Accept / ESC: Cancel / <<: Previous menu
4.4.2 Copy cycle name
This command allows for copying the name of cycle
from an existing one. The steps to follow are the
following:
After selecting COPY CYCLE NAME, press the
ENTER key and the first cycle name saved in the
memory will be displayed.
The INC (
∧∧∧∧∧
) and DEC (
∨∨∨∨∨
) keys display all the cycles
saved in the memory. Once the cycle has been selected,
press ENTER. It is now possible to change the cycle;
after changing press ENTER.
ENTER: Accept / ESC: Cancel / <<: Previous menu
4.4.3 Change cycle name
This command allows the cycle name to be modified
from amongst the names created by the user. The steps
to follow are the following:
After selecting CHANGE CYCLE NAME, press the
ENTER key and the first available cycle is displayed:
With the INC (
∧∧∧∧∧
) and DEC (
∨∨∨∨∨
) keys, the name to be
modified is selected. Press ENTER to validate the
selection.
Save cycle name?
Use the INC (
∧∧∧∧∧
) and DEC (
∨∨∨∨∨
) keys to modify the
character indicated by the cursor; use the ADVANCE
(>>) key to move the cursor to the next character. Once
the name has been modified, press ENTER.
ENTER: Accept / ESC: Cancel / <<: Previous menu
4.5 BLOCK
All the parameters of a block are described below and
the values that each one allows:
4.5.1 Stop program
With this parameter a program stop can be carried out
before the start of a cycle, that is to say, before the tub
begins to fill up with water or the drum starts to move.
This stop will be indicated by means of a message on
the screen and an acoustic signal. The options are:
YES
: the stop will be carried out.
NO : the stop will not be carried out.
4.5.2 Speed
This defines the drum’s turning speed. The different
options that can be programd are the following (in
revolutions per minute or rpm.):
From 30 to 70 in steps of 5: this is the washing speed.
From 300 to 1000 in steps of 50: this is the spinning
speed.
If a speed equal or higher than 300 rpm is programd, it
will be understood to be a spin, and so only two more
parameters can be programd: “Time” and “Unwinding”.
4.5.3 Rythm On
With this parameter, the running time of the drum than
be set. The drum will spin in one direction during the
running time and will stop in the stop time (“Rhythm
Off” parameter), and will then turn in the opposite
direction. The different options are:
From 3 to 99 seconds in steps of 1 running movement
of the drum.
4.5.4 Rythm Off
With this parameter, the running time of the drum can
be set. The drum will spin in one direction during the
running time and will stop in the stop time (“Rhythm
On” parameter), and will then turn in the opposite
direction. The different options are:
From 3 to 99 seconds in steps of 1 running movement
of the drum.
4.5.5 Hot water inlet
This serves to indicate if the hot water inlet is going to
be used to fill the tub. The options are:
YES
: the hot water inlet will be used.
NO : the hot water inlet will not be used.