ADC Campus-REX2 RS Скачать руководство пользователя страница 130

Страница: 130 / 166

Chapter 7 - Using the LCD for Configuration and Management

118

Campus-REX2 RS Interface Card User Manual

Router Port Statistics

To view the Router Port Statistics:

Press Escape until

CAMPUS RS I/F: REX2

is displayed.

Press Next until

REX2 CONFIG & STATUS

is displayed.

Press Enter.

CONFIGURE REX2 SETTINGS

is displayed.

Press Enter.

NETWORK PROTOCOL = Bridge

is displayed (if not,

you must change the setting to

Bridge

to view Bridge Port Statistics).

Press Next until

Bridge STATISTICS

is displayed.

Press Enter.

FRAMES

is displayed.

Press Enter to display the first screen of statistics.

Press Next to display the second screen of statistics (if any).

Press Escape.

FRAMES

(or the appropriate statistic title screen) is

displayed.

Press Next to advance to the desired statistic item, displayed in order:

MULTICASTS

ERRORS

UNDERSIZED

OVERSIZED

EX. DELAY

and

EX. COLLISIONS

. Repeat steps 7-9 as desired to display the

statistics for the item.

To clear the statistics, press Next until

Press ENTER to Clear

Statistics

is displayed. Press Enter to reset all statistics to zero.

Содержание Campus-REX2 RS







































































































































































Результаты поиска

Содержание Campus-REX2 RS

Отзывы:

Похожие инструкции для Campus-REX2 RS

Бренды по названию

Популярные бренды

ADC Campus-REX2 RS, Руководство пользователя

Результаты поиска

Содержание Campus-REX2 RS

Отзывы:

Похожие инструкции для Campus-REX2 RS

Бренды по названию

Популярные бренды