ADC Campus-REX2 RS Скачать руководство пользователя страница 129

Страница: 129 / 166

Chapter 7 - Using the LCD for Configuration and Management

Campus-REX2 RS Interface Card User Manual

117

•

number of frames received and transmitted

•

number of multicast frames received and transmitted

•

number of errored frames received and transmitted

•

number of undersized frames received

•

number of oversized frames received

•

number of excessive delay events for transmitted frames

•

number of excessive collision events for transmitted frames

•

number of bridge frames received and transmitted (Bridge only)

•

number of frames received that were discarded (Bridge only)

Bridge Port Statistics

To view the Bridge Port Statistics:

Press Escape until

CAMPUS RS I/F: REX2

is displayed.

Press Next until

REX2 CONFIG & STATUS

is displayed.

Press Enter.

CONFIGURE REX2 SETTINGS

is displayed.

Press Enter.

NETWORK PROTOCOL = Bridge

is displayed (if not,

you must change the setting to

Bridge

to view Bridge Port Statistics).

Press Next until Bridge

STATISTICS

is displayed.

Press Enter.

FRAMES

is displayed.

Press Enter to display the first screen of statistics.

Press Next to display the second screen of statistics (if any).

Press Escape to return to the statistics title screen.

Press Next to advance to the remaining statistic items, displayed in order:

MULTICASTS

BRIDGE

FRAMES

DISCARDS

ERRORS

UNDERSIZED

OVERSIZED

EX. DELAY

, and

EX. COLLISIONS

Repeat steps 7-9 as desired to display the statistics.

To clear the statistics, press Next until

Press ENTER to Clear

Statistics

is displayed. Press Enter to reset all statistics to zero.

Содержание Campus-REX2 RS







































































































































































Результаты поиска

Содержание Campus-REX2 RS

Отзывы:

Похожие инструкции для Campus-REX2 RS

Бренды по названию

Популярные бренды

ADC Campus-REX2 RS, Руководство пользователя

Результаты поиска

Содержание Campus-REX2 RS

Отзывы:

Похожие инструкции для Campus-REX2 RS

Бренды по названию

Популярные бренды