manualshive.com logo in svg

ADC Campus-REX2 RS, Руководство пользователя

Поделиться
Скачать
ADC Campus-REX2 RS Скачать руководство пользователя страница 123

 

Chapter 7 - Using the LCD for Configuration and Management

Campus-REX2 RS Interface Card User Manual

111

Viewing 24-Hour HDSL Alarm History

You can view the number of HDSL alarm conditions that have occurred over 
the past 24 hours. The LCD displays 24-hour information for the following 
alarms:

•

local errored seconds (

LOCAL ES

)

•

remote errored seconds (

REMOTE ES

)

•

local unavailable seconds (

LOCAL UAS

)

•

remote unavailable seconds (

REMOTE UAS

)

You may also view the time when the counter was last cleared and clear the 
counter. 

To view the HDSL alarm history:

1

Press Escape until 

CAMPUS RS I/F: REX2 

is displayed.

2

Press Next. 

HDSL LINK CONFIG & STATUS

 is displayed.

3

Press Enter, then press Next until 

PERFORMANCE STATUS

 is 

displayed.

4

Press Enter, then press Next to scroll through the alarm history is 
displayed.

5

To reset the counter, press Next until 

Press ENTER to clear 

error cnts

 is displayed, then press Enter.

Local Alarms

Loss of Signal (LOS) alarms can occur on the local unit. This section 
describes how to view and configure this alarm.

Viewing Current Alarms

If the 

CURRENT ALARMS

 display indicates a local alarm, you can determine 

the alarm type:

1

From the 

CURRENT ALARMS

 display, press Next twice. 

LOCAL I/F 

ALARMS CONFIG & STATUS

 is displayed.

2

Press Enter. The current status of the local alarm is displayed.

Содержание Campus-REX2 RS







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды