STOP
if you meet any resistance. The sensing unit is on the very tip of the probe
and there is no need to insert the probe deep into the rectum.
Dispose of the used probe cover and wash the thermometer as recommended. The
peak temperature should be reached in approximately 25-35 seconds.
Axillary Use:
Wipe armpit with a dry towel. Place the probe
in the patient’s armpit (Figure 3) and keep the patient’s arm
pressed firmly against the body. In order to achieve a better
axillary reading, a minimum measuring time of 90 seconds or
longer is recommended, depending on placement of the probe
and closure of the arm against the body.
Battery Replacement
1. When the symbol “ ” appears, the battery needs to
be replaced.
2. Remove battery compartment lid (Figure 4).
3. Use a pointed object such as a toothpick to pry loose the
old battery. Avoid using any sharp metal object.
4. Place new 1.55V coin-type battery (LR41 or equivalent) in the chamber with the
positive (+) side facing up or towards the display of the unit.
5. Replace the battery compartment lid.
Cleaning and Disinfecting
Do not use corrosive detergent to clean the unit.
Clean and disinfect the thermometer before and after each use.
Cleaning Process
1. Wipe probe with a cloth dipped in a disinfectant solution such as 70%
isopropyl (rubbing) alcohol or soap and water.
2. Rinse off disinfectant residue.
Care and Storage
• Do NOT drop or crush; this device is not shock proof.
• Do NOT dismantle or modify device other than replacing the battery.
• Do NOT store the device in an extreme environment with direct sunlight or high
temperatures.
• Store the unit in the protective case while not in use.
Figure 3
Figure 4
BATTERY
Specifications
Size:
5”L x 3/4”W x 3/8”H (12.7cm L x 1.9 cm W x .95 cm H)
Weight:
0.388 oz. (11 grams)
Display:
LCD, Liquid Crystal Display
Battery:
1.55V (LR41)
Battery Life:
Estimated 4,500 measurements
Measurement Time:
Oral 30* seconds / Rectal 25-35 seconds / Axillary 90 seconds
Measurement Range:
90.0°F to 109.9°F (32.0°C to 42.9°C)
96.0°F to 107.0°F
±
0.2°F / 1°C (34.0°C to 42.0°C)
at a room temperature of 64.4°F to 82.4°F (18.0°C to 28.0°C)
Accuracy:
90.0°F to 96.0°F
±
0.4°F / 0.2°C (32.0°C to 34.0°C)
and 107.0°F to 109.9°F (42.0°C to 42.9°C)
Measurement mode:
Real measurement with peak-hold method
Audible Alarm:
1 beep at start-up. Continuous beep at measurement completion
Auto Turn-off
In approximately 8 ±1 minutes
Memory:
Last reading
Operating Conditions:
50°F to 104°F (10°C to 40°C)
Humidity of 15% to 95% (non-condensing)
Storage Conditions:
-13°F to 131°F (-25°C to 55°C)
Humidity of 15% to 95% (non-condensing)
Standards:
Complies with EN 12470-3, ASTM E 1112-00,
IEC 60601-1, IEC 60601-1- 2, IEC 60601-1-11
Electromagnetic compatibility: device fulfills the stipulations
of standard IEC 60601-1-2
The manufacturer recommends a calibration check every 2 years.
*30-second response time achieved in water bath test.
LIMITED WARRANTY
ADC warrants its products against defects in materials and workmanship under normal house-
hold use and service as follows:
1. Warranty service extends to the original retail purchaser only and commences with the date
of delivery.
2. Your Adtemp Digital Stick Thermometer is warranted for two years from date of purchase.
What Is Covered:
Replacement of parts, and labor.
What Is Not Covered:
Transportation charges to ADC. Batteries where supplied. Damages
caused by abuse, misuse, accident, or negligence, incidental, special, or consequential
damages. Some states do not allow the exclusion or limitation of incidental, special, or
consequential damages, so this limitation may not apply to you.
To Obtain Warranty Service:
Send item(s) postage paid to ADC, Attn: Repair Dept.,
55 Commerce Dr., Hauppauge, NY 11788. Please include your name and address, phone no., proof
of purchase, and a brief note explaining the problem.
Implied Warranty:
Any implied warranty shall be limited in duration to the terms of this
warranty and in no case beyond the original selling price (except where prohibited by law).
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
For Australian Consumers:
Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonable foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
IB p/n 93-413-00 rev 8 (7/20/21)
Printed in China
LATEX
Microlife Corporation
9F, 431 RuiGuang Road
NeiHu, Taipei 114, Taiwan, R.O.C.
Medical Device Safety Service GmbH
(MDSS GmbH)
Schiffgraben 41, 30175 Hannover, GERMANY
Mfg. by: ADC
®
55 Commerce Drive, Hauppauge, NY 11788
Inspected in the USA
Made in China
Assembled in Vietnam
tel: 631-273-9600
toll free: 1-800-232-2670
fax: 631-273-9659
www.adctoday.com
email: [email protected]
1639
EC REP
