ADC AD-333, Руководство по установке, Страница: 8 / 18

8 American Dryer Corp. 112175 - 9
Installation Procedures ______________
Installation should be performed by competent technicians
in accordance with local and state codes. In the absence of
these codes, the installation must conform to applicable
American National Standards: ANSI.Z223.1-LATEST
EDITION (National Fuel Gas Code) or ANSI/NFPA NO. 70-
LATEST EDITION (National Electrical Code) or in Canada,
the installation must conform to Canadian Standards: CAN/
CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91
(L.P. Gas) or LATEST EDITION (for General Installation and
Gas Plumbing) or Canadian Electrical Codes Parts 1 & 2
CSA C22.1-1990 or LATEST EDITION (for Electrical
Connections).
Unpacking / Setting Up _______________
Remove protective shipping material (i.e., plastic wrap, and/
or optional shipping box) from dryer.
The dryer can be moved to its final location while still
attached to the pallet or with the pallet removed. To unpallet
the dryer, locate and remove the four bolts securing the base
of the dryer to the wooden pallet. Two are inside the lower
back guard at the rear base and two are located at the front
base. To remove the bolt located in the front, remove the lint
door. Once the bolts are removed, slide the dryer off the
pallet.
With the pallet removed, to make it easier to slide the dryer
into its final position, slightly lower all four leveling legs, so
that the dryer will slide on the legs instead of the base frame.
The dryer is equipped with four leveling legs, one at each
corner of the dryer base.
To increase bearing life and improve efficiency, the dryer
should be tilted slightly to the rear.
Location of the Dryer ________________
Before installing the dryer, be sure the location conforms to
local codes and ordinances. In the absence of such codes
or ordinances the location must conform with the National
Fuel Gas Code ANSI.Z223.1 LATEST EDITION, or in Canada,
the installation must conform to applicable Canadian
Standards: CAN/CGA-B149.1-M91 (Natural Gas) or CAN/
CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for General
Installation and Gas Plumbing).
The dryer must be installed on a sound level floor capable
of supporting its weight. Carpeting must be removed from
the floor area that the dryer is to rest on.
IMPORTANT: “The dryer must be installed on
noncombustible floors only.”
The dryer must not be installed or stored in an area where it
will be exposed to water and/or weather.
The dryer is for use in noncombustible locations.
The dryer must be installed with provisions for adequate air
supply as noted in this manual (refer to Fresh Air Supply
Requirements section).
Clearance provisions must be made from noncombustible
construction as noted in this manual (refer to Dryer
Enclosure Requirements section).
Provisions must be made for adequate clearances for
servicing and for operation as noted in this manual (refer to
Dryer Enclosure Requirements section).
Dryer must be exhausted to the outdoors in an area where
correct exhaust venting can be achieved as noted in this
manual (refer to Exhaust Requirements section).
Dryer must be located in an area where correct exhaust
venting can be achieved as noted in this manual (refer to
Exhaust Requirements section).
IMPORTANT: Dryer must be installed in a location/
environment, which the ambient temperature remains
between 40° F (4.44° C) and 130° F (54.44° C).
Dryer Enclosure Requirements ______
Bulkheads and partitions should be made of non-
combustible materials and must be located a minimum of
12-inches (30.48 cm), 18-inches (45.72 cm) or more is
recommended for ease of installation, maintenance, and
service, above the dryer outer top, except along the front of
the dryer, which may be closed in if desired. The clearance
between the bulkhead header and the dryer must be a
minimum of 4-inches (10.16 cm) and must not extend more
than 4-inches (10.16 cm) to the rear of the front.
IMPORTANT: If the dryer is installed in a closet type
enclosure there must be no other fuel burning appliance
installed in the same closet.
Dryers may be positioned sidewall to sidewall. However, a
1/16” (1.5875 mm) minimum allowance must be made for
opening and closing of the control door and the lint door. It
is suggested that the dryer be positioned about 2 feet (0.61
meters) away from the nearest obstruction for ease of
installation, maintenance, and service (to be measured from
the back guard). Refer to the illustration below for details.
Clearances shown are minimum dimensions to nearest
combustible materials.
NOTE A: 12-inch (30.48 cm) minimum, 18-inches (45.7 cm) is suggested for
ease of maintenance.
NOTE B: 12-inch (30.48 cm) minimum, 24-inches (61.0 cm) is suggested for
ease of maintenance.
NOTE: Fresh air considerations are important for proper
and efficient operation.