ADC AD-333, Руководство по установке, Страница: 15 / 18

112175 - 9 www.adclaundry.com 15
IMPORTANT: There is no regulator provided in an L.P.
dryer. The water column pressure must be regulated at
the source (L.P. tank) or an external regulator must be
added to each dryer.
Make a complete operational check of all safety related
circuits:
Door Switch(es)
Hi-Limit Thermostats
Cycling Thermostats
Sail Switch
Make a complete operational check of all operating controls.
NOTE: If computer program changes are required, refer
to the computer programming section of the manual
supplied with the dryer.
The dryer should be operated through one complete cycle
to ensure that no further adjustments are necessary and
that all components are functioning properly.
Tumbler Coating
The tumbler is treated with a protective coating. We suggest
dampening old garments or cloth material with a solution
of water and nonflammable mild detergent and tumbling
them in the tumbler to remove this coating.
Preoperational Instructions _________
Coin Models
Microprocessor Controller (Computer)
When the microprocessor controller (computer) is in the
ready state, the L.C.D. screen will display “FILL” followed by
the amount to start.
Insert coin(s). Once the correct “Amount to Start” has been
inserted, the L.C.D. will display “PUSH”.
Select temperature by pressing “HI,” “LO,” or “PERM
PRESS.” The cycle will start and the L.C.D. will display the
Dry Cycle selected and the remaining time.
The dryer will continue through the drying and cooling cycles,
until the vended time has expired.
NOTE: To stop the dryer, open the main door.
Continuation of the cycle will resume only after the door
has been closed and any of the three temperature
selection buttons is pressed.
Upon completion of the drying and cooling cycles, the tone
(buzzer) will sound and the dryer will go into the Anti-Wrinkle
Mode, if active, for up to 99 minutes, or until the main door or
lint drawer has been opened.
IMPORTANT: For more detailed information regarding the
microprocessor controller (computer) on your dryer, refer
to the microprocessor user’s manual included with the
dryer.
Shutdown Instructions _______________
If the dryer is to be shutdown (taken out of service) for a
period of time, the following must be performed:
Discontinue power to the dryer either at the external
disconnect switch or the circuit breaker.
Discontinue the gas supply (for gas models only):
Shut off external gas supply shutoff valve.
Service / Parts Information __________
Service
Service must be performed by a qualified trained technician,
service agency, or gas supplier. If service is required, contact
the reseller from whom the equipment was purchased. If
the reseller cannot be contacted or is unknown, contact the
Service Department for a reseller in your area.
NOTE: When contacting the Service Department, be sure
to give them the correct model number and serial number
so that your inquiry is handled in an expeditious manner.
Parts
Replacement parts should be purchased from the reseller
from whom the equipment was purchased. If the reseller
cannot be contacted or is unknown, contact the Parts
Department for a reseller in your area. Parts may also be
purchased directly from the factory by calling the Parts
Department at (508) 678-9000, FAX in your order at (508)
678-9447, or visit us online at www.adclaundry.com.
NOTE: When ordering replacement parts from the reseller
or the manufacturer, be sure to give them the correct
model number and serial number so that your parts order
can be processed in an expeditious manner.
Warranty Information ________________
Warranty Registration
Visit us at www.adclaundry.com and register all of your new
dryers by clicking on “Warranty” under the “Service” menu.
Warranty
For a copy of the commercial warranty covering your particular
dryer(s), contact the reseller from whom you purchased the
equipment and request a dryer warranty form. If the reseller
cannot be contacted or is unknown, warranty information
can be obtained from the factory by contacting the Warranty
Department at (508) 678-9000.
NOTE: Whenever contacting the factory for warranty
information, be sure to have the dryer’s model number
and serial number available so that your inquiry can be
handled in an expeditious manner.
Returning Warranty Parts
All dryer or parts warranty claims or inquiries should be
addressed to the Warranty Parts Department. To expedite
processing, the following procedures must be followed:
No parts are to be returned without prior written authorization
(R.M.A.) from the factory.