ADB Safegate RELIANCE Shallow Base Скачать руководство пользователя страница 40

Страница: 40 / 46

Table 2: Accessories and spare parts

Description

Image example

Obstruction Cap

•

Plastic obstruction cap, PG 16 thread.

Applicable for all side entry base versions.

M10 locking nuts

•

Plated Brass M10 locking nut.

Applicable for all stud bolt base versions.

HEX Screw M10×25 mm

•

Stainless steel HEX Screw M10×25 mm.

Applicable for all M10 insert thread base versions.

HEX Screw UNC3/8”×1”

•

Stainless steel HEX UNC3/8”×1”.

Applicable for all UNC insert thread base versions.

Ground screw

•

DIN7504K

•

Stainless steel

•

M4.8×16 mm

Applicable for all Base 8”/12” versions.

Stud bolt M10

•

Stainless steel stud bolt

•

M10 (upper thread) and M10 HeliCoil (lower thread)

O-ring gasket for 8” base

O-ring gasket for 12” base

Order Codes

Table 3: Accessory kits

Description

Quantity per

Order Code SGXXXXX

fitting

order

Accessory kit 1:

Two-core cables connector kit including cable

1 or 2

13127

Accessory kit 2:

One-core cable Ø 9-12 mm connector kit

1 or 2

17770

Side entry cable connector kit with tube

1 or 2

17851

RELIANCE Shallow Base
Spare Parts

30
Copyright

Содержание RELIANCE Shallow Base







































Результаты поиска

Содержание RELIANCE Shallow Base

Отзывы:

Похожие инструкции для RELIANCE Shallow Base

Бренды по названию

Популярные бренды

ADB Safegate RELIANCE Shallow Base, Руководство пользователя

Результаты поиска

Содержание RELIANCE Shallow Base

Отзывы:

Похожие инструкции для RELIANCE Shallow Base

Бренды по названию

Популярные бренды