manualshive.com logo in svg

ADB Safegate RELIANCE Omni 1-Dome, Руководство пользователя

Поделиться
Скачать
ADB Safegate RELIANCE Omni 1-Dome Скачать руководство пользователя страница 46

6.4.10 Replacing the LED Board Assembly

The LED board assembly includes the LED, the connection board and the bracket.

NOTICE

Replace the lens gasket to mount the LED board assembly when a new fixture is delivered. The lens gasket that is

mounted upon receipt are only mounted as a transportation protection. Make sure you throw it away!

WARNING

Turn off the circuit before replacing LEDs. Failure to observe this warning may result in personal injury, death, or

equipment damage.
Failure to follow this instruction can result in injury or equipment damage.

Note

Refer to the 

Spare Parts

 section.

To replace the LED assembly, perform the following procedure:

1. Open the light assembly.

Refer to 

Disassembling the Light Fixture

 section.

2. Refer to 

Replacing LED Assembly

 figure.

Unscrew the two M6 torx head screws that fasten the LED Optical Assembly bracket to the top cover. Remove the brackets

from the prisms being in place when they are delivered to mount the LED board.

RELIANCE Omni 1-Dome,
Maintenance

36
Copyright 

©

 ADB SAFEGATE, All Rights Reserved

Содержание RELIANCE Omni 1-Dome



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды