manualshive.com logo in svg

ADB Safegate RELIANCE Omni 1-Dome, Руководство пользователя

Поделиться
Скачать
ADB Safegate RELIANCE Omni 1-Dome Скачать руководство пользователя страница 44

Figure 17: Lens Gasket

Figure 18: Grease Application

7. Clean the lens recess in the cover thoroughly with any effective solvent.
8. Place the lens with the Lens Gasket back.

Make sure that you use a new Lens Gasket.

9. Place the Flat Gasket back.

Make sure you use a new Flat Gasket.

10. Close the light fixture.

Refer to 

Assembling a 8

‑

inch Fixture 

section.

6.4.9 Replacing the Top Cover Assembly

NOTICE

Top covers are delivered without the LED board assembly. LED board assemblies have to be ordered separately.

1. Open the light assembly: Refer to 

Disassembling the Light Fixture

 section.

2. Disconnect the top cover from the bottom cover.
3. Use a new top cover and go to 

Assembling a 8

‑

inch Fixture 

section.

RELIANCE Omni 1-Dome,
Maintenance

34
Copyright 

©

 ADB SAFEGATE, All Rights Reserved

Содержание RELIANCE Omni 1-Dome



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды