manualshive.com logo in svg

ADB Safegate RELIANCE Omni 1-Dome, Руководство пользователя

Поделиться
Скачать
ADB Safegate RELIANCE Omni 1-Dome Скачать руководство пользователя страница 17

3.0 General Information

WARNING

Read installation instructions in their entirety before starting installation.

•

Become familiar with the general safety instructions in this section of the manual before installing, operating,

maintaining or repairing this equipment.

•

Read and carefully follow the instructions throughout this manual for performing specific tasks and working with

specific equipment.

•

these warnings may result in serious injury or equipment damage.

Figure 1: RELIANCE Omni, 1 Dome

3.1 Introduction to RELIANCE

RELIANCE - the all in one revolution
The RELIANCE omnidirectional light light is a low protrusion light-emitting diode (LED) fixture, available in three versions:

RELIANCE NON-

MON

A LED light fixture without monitoring (No CCR monitoring or ILCMS

compatibility)

RELIANCE MON

A LED light fixture with integrated fail open technology with CCR monitoring

compatibility

RELIANCE IQ

A RELIANCE with additional and integrated intelligence (IQ) in a built-in converter

for individual monitoring and control, based on RELIANCE Intelligent Light

Control and Monitor System (ILCMS)

RELIANCE IQ0

RELIANCE IQ light fixture with disabled IQ (ILCMS) functionality. Non-MON light

fixture with possibility to activate IQ at a later stage

UM-5073, Rev. 1.0, 2021/07/13

7

Copyright 

©

 ADB SAFEGATE, All Rights Reserved

Содержание RELIANCE Omni 1-Dome



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды