ADB Safegate L-858 AGSF Series Скачать руководство пользователя страница 32

Страница: 32 / 56

3.4 Sign Mounting and Installation

WARNING

Signs must be grounded to a true earth ground. Failure to observe this warning may result in personal injury, death, or

equipment damage.

3.4.1 General Guidelines

When installing signs, follow the guidelines below

•

See FAA AC 150/5340-30, Fig 126 for mounting pad design. Also see the following subsections for detailed

information on sign pad and leveling of the sign.
FAILURE TO INSTALL AND LEVEL THE SIGN AS DESCRIBED IN THE VARIOUS SUBSECTIONS BELOW WILL VOID THE

WARRANTY

•

Mount the signs on a concrete slab or concrete pedestals

•

Do not allow concrete edges to protrude above grade.

•

Provide power to the signs through breakaway cable connectors installed within the frangible coupling portion of the

sign’s mounting legs.

•

Install auxiliary equipment, such as isolation transformers, in a light base embedded in the ground.

3.4.2 Overall Mounting Height

Install signs so that the overall height above the surrounding ground of the sign assembly, including mounting supports, does

not exceed heights given in

Table 6

and the clearances of aircraft wings as specified in AC 150/5340-18. The sign must

provide 12 inches (304.8 mm) of clearance between the top of the sign and any part of the most critical aircraft using, or

expected to use, the airport when the aircraft’s wheels are at the pavement edge. For overall mounting height, refer to AC

150/5345-44.

3.4.3 Sign Orientation

When orienting signs follow the guidelines below

•

Orient the sign so that the face is perpendicular to the centerline of the taxiway or runway.

L-858 AGSF
Installation

22
Copyright

Содержание L-858 AGSF Series





















































Результаты поиска

Содержание L-858 AGSF Series

Отзывы:

Похожие инструкции для L-858 AGSF Series

Бренды по названию

Популярные бренды

ADB Safegate L-858 AGSF Series, Руководство пользователя

Результаты поиска

Содержание L-858 AGSF Series

Отзывы:

Похожие инструкции для L-858 AGSF Series

Бренды по названию

Популярные бренды