ADB Safegate IDM 8000 Скачать руководство пользователя страница 61

Страница: 61 / 118

5.0 Installation

5.1 General

This section deals with the installation of the CCR. Please refer to specific wiring diagrams and mechanic drawings for detailed

information.

5.1.1 Air conditioning

NOTICE

Make sure you use air conditioning to reduce the risk of equipment damage!

The table below lists the heat dissipation values of the CCR:

Table 1: Air conditioning relevant values

Power Rating

Heat Dissipation (W)

3 kVA

300

4 kVA

400

5 kVA

500

7.5 kVA

750

10 kVA

1000

12.5 kVA

1250

15 kVA

1400

17.5 kVA

1500

20 kVA

1600

25 kVA

2000

30 kVA

2400

5.1.2 Transportation, Unpacking and Storage

Transportation
Make sure to do the following regarding transportation:

NOTICE

Keep the CCR always in upright position during transportation and storage.
Protect the CCR from adverse weather conditions.

Make sure to do the following upon receipt:

UM_IDM-8000, Rev. 1.7, 2021/05/06

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды