ADB Safegate IDM 8000 Скачать руководство пользователя страница 58

Страница: 58 / 118

Setting sequence

1. Go to system settings by selecting Set/Set/More/Sys.

1. Browse the desired parameter with Next, adjust it with + / - and select Set to confirm.

1. If the CCR is with direction changer, select the other direction and set required parameters.

4.6.9 Remote control settings

These general remote control settings are only enabled when the control switch is in Off-position.

Note

: ERR indication is provided if settings are not accepted.

The CCR automatically detects if serial or parallel or no remote control card is connected and provides setting menus

accordingly:

•

Rcmode: Display only, serial (computerized) or parallel control card or no card detected.

•

Bustype: Serial mode only. Displays which type of fieldbus card is detected (e.g. Profibus)

•

Fieldb: Serial mode only, tells if 1 or 2 (redundant system) serial cards are detected

•

Fails: Serial mode only. Failsafe mode i.e. what happens in case of bus failure:

Setting Function

Cont

Continues with selected control status

Selects the failsafe step 0-7 (failsafe)

Fs off

Selects the failsafe step only if control status is Off, else continues with selected control stat.

ContHB Continues with selected control status, Heart beat signal is used for bus failure detection.

Fs HB

Selects the failsafe step 0-7 (failsafe), Heart beat signal is used for bus failure detection.

Fs of HB Selects the failsafe step only if control status is Off, else continues with selected control stat. Heart beat signal is used for bus

failure detection.

In case of direction changer CCR dir 1 is considered as failsafe direction and all circuits with circuit selector CCRs.

•

F step: Serial mode only. Select a failsafe step if Fs or Fs off modes are selected

•

Dec/bin: parallel mode only: coding of control signals.

•

Cont/imp: parallel mode only: mode of control signals

•

ComF-m: defines if all fault signals are summed to Com-fault indication (SumF) or it contains only U1, f1 and T alarms

(SysF).

Displays with serial remote control card detected:

Header / function

Data 1

Data 2

Fact set

Allowed range

Remote control set

Serial/ none

Rcmode

* Project

Autodetect

Bustype

* Project

Autodetect

No of serial cards

Fieldb

* Project

Autodetect

Failsafe mode

Fails

Cont

Cont / Fs / Fs off / ContHB / FS HB / FsofHB

Failsafe step

F step

0-7

IDM 8000
User Interface

46
Copyright

Содержание IDM 8000







































































































Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды

ADB Safegate IDM 8000, Руководство пользователя

Результаты поиска

Содержание IDM 8000

Отзывы:

Бренды по названию

Популярные бренды