ACV ACVMax Touch Скачать руководство пользователя

Страница: 7 / 48

Installer's Handbook (Evo) - 660Y3000 • A

INSTALLER CODE

Through the use of the specific code "

054

", the installer can access various setup

screens, in order to define a large set of parameters and adapt the operation of the

ACVMax to the system configuration.

To navigate on the screen, use the

UP, DOWN, LEFT

and

RIGHT

soft keys

, then

the

key to validate a selection. To increase/decrease values, use the

and

DOWN

soft keys. or

LEFT

and

RIGHT

, according to the situation.

Entering the installer access code allows the installer to make adjustments for

30 minutes. After 30 minutes, the access code will have to be entered again to

make any adjustments.

INSTALLER MENU DESCRIPTION

The installer Menu contains the following icons :

CH & DHW Settings

–

Allows the installer to adjust the appliances central/space

heating and domestic hot water settings for the application. For the detail of the
menus, go to

"CH & DHW Settings ( ) "

Manual Operation

–

The burner and circulators can be manually enabled for testing.

For a detail of the menus, go to

"Manual Operation ( )"

Cascade

Settings

– Although the menu is visible, it is not active for the Evo

models. Refer to the "Installation, Operation and Maintenance manual" of the units

for more information on cascade possibilities

Reset All Settings

–

Resets all CH and DHW Settings back to the default settings

(for the detail of the values, go to

"Factory settings and reset values"

For a detail

of the menus, go to

"Reset all settings ( )"

Home

to go back to the home page.

6. Back -

to go back to the previous screen.

Boiler Protection

DHW

84°C

61°C

System pressure= 1.5 bar

HeatMaster

ENTER ACCESS CODE

05[4]

CH Settings

CH & DHW Settings

Reset All Settings

Press OK

to restore factory settings,

any other button

to keep current settings.

Cascade Info.

Manual Operation

FAN

CH1

CH2

DHW

Released

Off

Select a position using the

LEFT

and

RIGHT

soft keys, and

increase or decrease the digit

value using the

and

DOWN

soft keys.

INSTALLER MENU STRUCTURE

CH & DHW Settings

Reset All Settings

Cascade Information

Manual Operation

The Cascade feature is not

applicable to EVO units and is

not described in this manual.

Touch

and

simul-

taneously for 5 seconds

DESCRIPTION AND OPERATION

Содержание ACVMax Touch

















































Результаты поиска

Содержание ACVMax Touch

Отзывы:

Похожие инструкции для ACVMax Touch

Бренды по названию

Популярные бренды

ACV ACVMax Touch, Руководство по установке

Результаты поиска

Содержание ACVMax Touch

Отзывы:

Похожие инструкции для ACVMax Touch

Бренды по названию

Популярные бренды