ACV ACVMax Touch Скачать руководство пользователя страница 30

Страница: 30 / 48

Installer's Handbook (Evo) - 660Y3000 • A

ELECTRICAL CHARACTERISTICS - 25 TO 45 KW EVO APPLIANCES

230 VAC OUTPUT !

Key

230 V power supply

Ground

ON/OFF master switch

Gas valve rectified

Burner power supply

Terminal block for optional items

: Alarm (ERR)

: DHW circuit circulator pump (DHW)

7. Terminal block for optional items:

: Pump (P3 and P4 terminals)

: Flame terminal (versatile connection according to configuration)

Modulating pump PWM

Burner PWM plug

10.

NTC5 flue gas temperature sensor

11.

NTC2 return sensor

12.

NTC1 supply sensor

13.

NTC - Low temperature circuit

14.

High limit switch

15.

Low water pressure sensor

16.

PCB (Display)

17. ACVMax programmation plug

18.

A & B Modbus (option)

19.

NTC3 DHW sensor

20. NTC4 outdoor temperature sensor (option)

21.

Room thermostat 1 (option)

22.  0-10 Volt (option)
23.  Room thermostat 2 (option)
24.  Connection for interface control unit
25.  Ignition and ionization cable
26.  5AT slow-blow fuse (3x) for internal and optional circuits*
27.  10A fuse, 250V, Dim: 5x20 mm

* 5AT slow-blow fuse (2x) for internal circuits and connection of CH, DHW and Flame 5AT slow-blow fuse (1x) for con-

nection of Alarm, P3 and P4 (connector P14)

2 spare 5AT slow-blow fuses are located on the back side of the electrical box, for fuse replacement, if required.

HeatMaster (T)C Evo

Main Characteristics

Rated voltage

230

Rated frequency

Electrical consumption

Max.

111

126

Min.

Electrical consumption

at 30% load

Electrical consumption

in standby

Rated current (Fuse)

Class

IP 20

WaterMaster Evo

Main Characteristics

25(X)

45(X)

Rated voltage

230

Rated frequency

Electrical consumption

Max.

110

126

Min.

Electrical consumption at

30% load

Electrical consumption in

standby

Rated current (Fuse)

Class

IP 20

SYSTEM DIAGRAMS AND SET-UP

Содержание ACVMax Touch

















































Результаты поиска

Содержание ACVMax Touch

Отзывы:

ACV ACVMax Touch, Руководство по установке, Страница: 30 / 48

Результаты поиска

Содержание ACVMax Touch

Отзывы: