background image

 

Infrared Modem User’s Manual 

 

 

Page

 

15

 

of

 

41

Revision 1.0 

2003/11 From 3JTech

 

For Connecting PSION using Serial Cable 

This section uses PSION 5 as an example. 

(1)

 

Hardware needed 

1.

 

Pegasus III series modem 

2.

 

Psion 5 

3.

 

Null modem cable 

(The Serial Cable synchronizes the PSION 5 and the Pegasus modem. One end 

of the cable is a 9-pin RS-232 male connector that connects to the female 

RS232 9-pin serial cable provided by PSION series 5. The other end is the 

PCMCIA male connector that connects to Pegasus modem. Please follow the 

following steps) 

(2)  Software needed 

Message Suite   

(Using your PC, go to 

www.psion.com

 and download software for modem 

control. The modem software consists of (E-mail), web, and modem setup 

software). The software is called "

Message Suite" 

and it is available at 

www.psion.com/downloads/mssgsuite.html

 (After downloading and installing 

"

Message Suite" 

to the your PSION 5, verify that the software has been 

successfully installed.) 

 

(3)   Connect the modem to PSION 5 series 

Connect one end of the male 9-pin RS-232 (shorter one, included) into the female 

9-pin RS-232 cable connected to the rear of the PSION 5. Connect the other end 

of the PCMCIA connector into the socket to the rear of the modem.   

(Refer to the connection diagram on next page) 

Insert one end of the phone cord (included) into the Pegasus modem’s LINE 

jack and plug the other end into any analog phone jack. Important: Connect to 

an analog line only. Using a non-analog line (e.g., digital, PBX, Multi line) 

may damage the modem. 

 

(4)  PSION 5 Remote Dial-Up Connection Setup 

 

1. Tap 

on 

"Extras"

. You should see web and e-mail. If you don’t, then you 

need to reinstall the software. Contact 

PSION

 for assistance.   

2.  Continue by going to 

"Control panel"

, and tap on 

"Modem"

. Choose 

"Hayes compatible modem"

 under 

Modem Settings

, and then tap 

"Edit" 

 

Содержание PP2-5600










































Отзывы: