Actel ProASIC3/E Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 106

Actel ProASIC3/E Скачать руководство пользователя страница 23

ProASIC3/E Starter Kit User’s Guide and Tutorial

23

3

Setup and Self Test

This chapter outlines how to set up and test the ProASIC3/E Evaluation Board.

Software Installation

The ProASIC3/E Starter Kit includes the Libero® Integrated Design Environment (IDE) software (version 2.3 SP2).
For Libero IDE software installation instructions, refer to the

Actel Libero IDE / Designer Installation and Licensing

:

http://www.actel.com/documents/install_ug.pdf.

Hardware Installation

FlashPro3 is required to use the ProASIC3/E Starter Kit. For software and hardware installation instructions, refer to
the

FlashPro User’s Guide

:

http://www.actel.com/documents/flashpro_ug.pdf

Testing the Evaluation Board

Refer to

“Test Procedures for Board Testing” on page 67

.

Programming the Test File

To retest the evaluation board at any time, use the test program to reprogram the board. Use the TOP_A3PE.stp file
with an A3PE600-PQ208 fitted on the board. Use TOP_A3P.stp with an A3P250-PQ208 fitted on the board.

This design is currently implemented for the A3PE600 die size. For a device of a different size, it is possible to recompile
the design into other device sizes. For information about retargeting the device, refer to the

Designer User’s Guide

at

http://www.actel.com/documents/designer_ug.pdf

. The design files are available under actelprj/eval in the Starter Kit

CD.

For instructions on programming the device using FlashPro3, refer to the FlashPro User’s Guide.

«
...
21
22
23
24
25
...
»

Содержание ProASIC3/E











































































































Отзывы:

Нет отзывов