background image

47

Marvair MGA3090-3180 Wall Mount AC I&O Manual 05/2023 Rev.14

Chapter 7 Warranty

7.1 

Marvair, Inc.  Limited Product Warranty

Marvair Inc., warrants its products to be free from defects in materials and workmanship under normal use to the original purchaser 

for the period of time in the table below. If any part of your  product fails within 12 months from start-up, or 18 months from 

shipment from the factory,  whichever comes first, Marvair, Inc.  will furnish without charge, EXW Cordele, Georgia, the required 

replacement part. The owner must provide proof of the date of the original start-up. The contractor’s invoice, the certificate of 

occupancy, or similar documents are examples of acceptable proof of the date of the original start-up.

Marvair, ICE, Eubank Products

90 Days

1

 w/Flat Rate Labor

2

 (See Marvair, ICE, Eubank Flat Rate Labor Guidelines)

1 Year Parts

2,3

5 Years Compressor

2

1

If any part of your Marvair, Inc.  unit fails within 90 days of the commencement of the warranty, Marvair, Inc.  will furnish without charge, EX Works, Cordele, Georgia, the 

required replacement part and pay for the labor to replace the part in accordance with the Marvair, Inc. Flat Rate Labor Guidelines.

2

All OTR (over the road) applications that are moved from one location to another: Factory Warranty applies only up to the point of initial start-up and test at all OEM 

manufacturing locations or subsequent facility. Once it goes into OTR service, the warranty expires immediately for compressor and sealed system components. This OTR 

exemption does not apply to relocatable classrooms, construction or office trailers.

3

All warranty replacement parts shall be shipped Ground only. Expedited shipping is available upon request for additional cost.

The responsibility of the equipment owner includes:

1.  To operate the equipment in accordance with the manufacturer’s instructions.

2.  To provide easy accessibility for servicing.

3.  To check and reset any circuit breaker(s) and/or disconnect(s) prior to calling for service.

4.  To keep the unit clean and free of dirt and containment and replace filters as required.

5.  To keep the outdoor coil clean and free of leaves, paper, or other debris.

6.  To pay the charges incurred when any of the above have not been done.

7.  To pay for repair or replacement of any material or part other than those within the Marvair unit or controller.

Marvair, Inc.,  will not be responsible for labor after 90 days, transportation costs, delays or failures to complete repairs caused by 

events beyond our control (labor hours incurred due to required site-specific training, time waiting to gain access, or extended drive 

time for remote sites). This warranty does not cover:

1.  Any transportation, related service labor, diagnosis calls, filter, driers, refrigerant, or any other material charges.

2.  Damages caused by shipping, accident, abuse, negligence, misuse, fire, flood, or Acts of God.

3.  Damages caused by operating or staging the unit in a corrosive environment.

4.  Damages caused by improper application of the product.

5.  Damages caused by failing to perform proper routine maintenance.

6.  Expenses incurred for erecting, disconnecting or dismantling the product or installing the replacement part(s).

7.  Products not installed or operated according to the included instructions, local codes, and good trade practices.

8.  Products moved from the original installation site.

9.  Products lost or stolen

10.  Consequential damages or incidental expenses including losses to persons, property or business.

11.  Modifications to original unit after it leaves the factory, such as breaking into any part of the sealed systems unless 

authorized in advance in writing by Marvair, Inc.. 

12.  Damages as a result of operating as a construction site cooler / dehumidifier.

When labor (first 90 days only)  is required, it must be performed during normal working hours (8:00 AM - 5:00 PM) Monday - Friday 

and must be performed by Marvair, Inc.,  personnel or a designated Service Representative. 
The owner of the product may ship the allegedly defective or malfunctioning product or part to Marvair, Inc.,, at such owner’s 

expense, and Marvair, Inc.,  will diagnose the defect and, if the defect is covered under this warranty, Marvair, Inc.,  will honor its 

warranty and furnish the required replacement part. All costs for shipment and risk of loss during shipment of the product to 

Marvair, Inc., and back to the owner shall be the responsibility and liability of the owner. Upon written request by an owner, Marvair, 

Inc., may arrange for remote diagnosis of the allegedly defective or malfunctioning product or part but all costs for transportation, 

lodging and related expenses with regard to such diagnostic services shall be the responsibility and liability of the owner.
An owner requesting performance under this Warranty shall provide reasonable access to the allegedly defective or malfunctioning 

product or part to Marvair, Inc., and its authorized agents and employees.
THIS WARRANTY CONSTITUTES THE EXCLUSIVE REMEDY OF ANY PURCHASER OF A MARVAIR HEAT PUMP OR AIR CONDITIONER 

AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY 

OF MERCHANTABILITY OR FITNESS FOR USE, TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO EVENT SHALL ANY IMPLIED 

WARRANTY OF MERCHANTABILITY OR FITNESS FOR USE EXCEED THE TERMS OF THE APPLICABLE WARRANTY STATED ABOVE 

AND MARVAIR SHALL HAVE NO OTHER OBLIGATION OR LIABILITY. IN NO EVENT SHALL MARVAIR BE LIABLE FOR INCIDENTAL OR 

CONSEQUENTIAL DAMAGES OR MONETARY DAMAGES.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE-TO-

STATE. Some states do not allow limitations or exclusions, so the above limitations and exclusions may not apply to you.  

Содержание Marvair MGA3090A






















































Отзывы: