Acromag TT231-0600 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 41

Acromag TT231-0600 Скачать руководство пользователя страница 34

Model TT231-0600

Two-Wire RTD Transmitter w/USB

Acromag, Inc. Tel: 248-295-0880

- 34 - http://www.acromag.com

- 34 -

http://www.acromag.com

ACCESSORIES

Software Interface Package

Software Interface Package/Configuration Kit

– Order TTC-SIP



USB Signal Isolator



USB A-B Cable 4001-112



USB A-mini B Cable 4001-113



Configuration Software CDROM 5040-944

This kit contains all the essential elements for configuring TT230 & TT330
family Transmitters. Isolation is recommended for USB port connections to
these transmitters and will block a potential ground loop between your PC
and a grounded current loop. A software CDROM is included that contains
the Windows software used to program the transmitter.

USB Isolator

USB Isolator

– Order USB-ISOLATOR



USB Signal Isolator



USB A-B Cable 4001-112



Instructions 8500-900

This kit contains a USB isolator and a 1M USB A-B cable for connection to a
PC. This isolator and cable are also included in TTC-SIP (see above).

USB A-B Cable

USB A-B Cable

– Order 4001-112



USB A-B Cable 4001-112

This is a 1 meter, USB A-B replacement cable for connection between your
PC and the USB isolator. It is normally included with the TTC-SIP Software
Interface Package and also with the isolator model USB-ISOLATOR.

USB A-mini B Cable

USB A-mini B Cable

– Order 4001-113



USB A-mini B Cable 4001-113

This is a 1 meter, USB A-miniB replacement cable for connection between
the USB isolator and the TT230 transmitter. It is normally included in TTC-
SIP.

Note that software for all TT Series models is available free of charge,
online at www.acromag.com.

«
...
32
33
34
35
36
...
»

Содержание TT231-0600










































Отзывы:

Нет отзывов