manualshive.com logo in svg

Acromag microBlox Series, Руководство пользователя, Страница: 21 / 29

Поделиться
Скачать
Acromag microBlox Series Скачать руководство пользователя страница 21

microBlox® Transmitter/Alarm Carrier 

                        Model uBTA-H-1MR/uBTA-H-1SR/uBTX-H-1 

 

 

Acromag, Inc. Tel: 248-295-0880  

            - 21 -                                   

http://www.acromag.com  

- 21 - 

https://www.acromag.com 

 

 

ACCESSORIES 

 

DIN Rail Bus Connector Kit 

 

 

Model XTBUS-KIT Bus Connector Kit for DIN Rail Bus Connection to Power, 
compatible with enclosures of Acromag Series XT and uBTA-H product 
models. 

 
This kit contains one each of the following terminals  
 

•

 

DIN Rail Bus Connector 1005-070 for 22.5mm Enclosures.  

•

 

Left Side terminal block, female connector 1005-220.  

•

 

Right Side terminal block, male connector 1005-221. 

•

 

Two End Stops for 35 mm DIN Rails 1027-222 (not shown). 

 
The module is shipped with the first item included in this kit, DIN Rail Bus 
Connector 1005-070--this kit offers a spare. Left and right side terminal blocks 
that mate directly to the bus connector are also included in this kit. These 
terminals are used to optionally (or redundantly) drive power to the carrier 
via its DIN rail bus connector.  This allows modules to neatly and conveniently 
share connections to Power by plugging enclosures together. Two DIN rail 
end stops 1027-222, are used to secure the terminal block and module(s) to 
the DIN rail for hazardous location installations. 
 

NOTE:

  The maximum number of modules that can be plugged-together and 

powered from a bus connection will be limited by twice its combined current 
draw at a given supply voltage below 3A of maximum allowable current.  This 
allows you to safely fuse the DIN rail bus power connection with a surge-
tolerant fuse no greater than 2.5A (recommended).  Note that current draw is 
normally reduced at higher input voltages and current to the unit(s) should 
never be allowed to exceed 3A even for bussed powered units.  Sustained 
current at 3A or above may damage the power circuit, and this could occur 
for an over-loaded bus or a sustained over-voltage condition that could drive 
an inadvertent short-circuit for a clamped transient voltage suppressor across 
the input power terminals of a unit. 

 

 

End Stops 

 

 

Two End Stops 

–

 

Order 4001‐252

 

•

 

Two 1027‐222 End Stops for 35 mm DIN Rail

 mounting 

 

For hazardous location installations (Class I, Division 2 or ATEX / IECEx 

Zone 2), you can use two end stops (Acromag 1027‐222) to help secure 

modules to 35mm DIN rail (not shown). 
 

 
 

 

 

FEMALE 1005-220

LEFT-SIDE

NORMALLY PROVIDED

WITH XT MODULE

MALE 1005-221

RIGHT-SIDE

DIN RAIL BUS

CONNECTOR 1005-070

CONNECTOR

CONNECTOR

Содержание microBlox Series






























Отзывы:

Нет отзывов