![ACOEM Met One Instruments GAS-1060 Скачать руководство пользователя страница 48](http://html1.mh-extra.com/html/acoem/met-one-instruments-gas-1060/met-one-instruments-gas-1060_user-manual_459535048.webp)
Serinus 60 User Manual 3.0
Page 48
Span Compensation
When
Enabled
the instrument will automatically perform a
Span
Calibrate NO2
at the end of the
Cycle Time
and adjust the gain
based on the
Span Level
.
When
Disabled
it will do a precision check only, no adjustment is
made.
Timed
mode with span compensation enabled does not fulfil U.S.
EPA approval or EN certification.
Span Level
Enter the concentration of span gas expected. Used when the
Span Compensation
is
Enabled.
3.4.11
Pressure Calibration Menu
Main Menu
Calibration Menu
Pressure Calibration Menu
Entering this menu will set the valves to the pressure calibration configuration; leaving the menu will
restore the valves to normal operation (refer to Section 5.2).
Vacuum Set Pt.
The zero point for the calibration. Activating this item will open a
dialog box of instructions.
Ambient Set Pt.
The high point for the calibration. Activating this item will open a
dialog box of instructions.
Pressure Units
Select the units that the pressure will be displayed in (
torr
,
PSI
,
mBar
,
ATM
or
kPa
).
Ambient
The current ambient pressure.
The current ambient pressure displayed as a raw voltage.
Cell
The current pressure in the measurement cell.
The current measurement cell pressure displayed as a raw voltage.
3.4.12
Service Menu
Main Menu
Service Menu
Diagnostics Menu
Refer to Section 3.4.13.
Calculation Factors Menu
Refer to Section 3.4.20.
Load Auto-Backup Config.
Loads the auto-backup configuration file. The configuration is
automatically backed up every night at midnight.
Load Configuration
Loads a user selectable configuration file from the USB memory
stick.
Save Configuration
Saves all of the EEPROM-stored user-selectable instrument
configurations to the USB memory stick (calibration and
communication settings, units, instrument gain, etc.). If there are
problems with the instrument use this function to save settings to
the USB memory stick and send this file (together with the
parameter list save) to your supplier with your service enquiry.
Содержание Met One Instruments GAS-1060
