background image

2

D

 

1. Safety Instructions

WARNING

 

 

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure 

that they also receive this instruction booklet. 

 

Unpack and check carefully there is no transportation damage before using the unit. 

 

Before operating, ensure that the voltage and frequency of power supply match the power 

requirements of the unit.   

 

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock. 

 

The unit is for indoor use only. Use only in a dry location. 

 

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent 

surfaces. Be sure that no ventilation slots are blocked.   

 

Disconnect main power before replacement or servicing.   

 

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.   

 

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always 

by taking its base.     

 

Maximum ambient temperature is Ta: 0-40

.   

 

Unit surface temperature may reach up to 60

. DO NOT touch the housing bare-hand during its 

operation.  Turn off the power  and allow about 15 minutes  for the unit  to cool down before 

replacing or serving. 

 

In the event of serious operating problem, stop using the unit immediately. Never try to repair 

the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. 

Please contact the nearest authorized technical assistance center. Always use the same type 

spare parts. 

 

DO NOT touch any wire during operation as high voltage might be causing electric shock. 

Warning: 

 

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or 

Please read carefully the instruction, which includes important 

information about the installation, usage and maintenance. 

Содержание NEBULA





















Отзывы: