ACME NEBULA Скачать руководство пользователя | Manualshive

Страница: 16 / 20

background image

15

D

6. Troubleshooting

Following are a few common problems that may occur during operation. Here are some

suggestions for easy troubleshooting:

A. The unit does not work, no light and the fan does not work

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

«
...
14
15
16
17
18
...
»

Содержание NEBULA





















Отзывы:

Нет отзывов

Похожие инструкции для NEBULA

Бренд: Acer Страницы: 3

Бренд: Acer Страницы: 2

Бренд: Barco Страницы: 72

Бренд: BenQ Страницы: 2

Бренд: BOXLIGHT Страницы: 55

Бренд: afx light Страницы: 7

Бренд: GAF Страницы: 12

Бренд: BenQ Страницы: 57

Бренд: Light Sky Страницы: 26

Burstberry Series

Бренд: KVANT Страницы: 29

Бренд: KVANT Страницы: 28

Бренд: KVANT Страницы: 33

Innovate CP-AW100N

Бренд: Hitachi Страницы: 202

Бренд: Barco Страницы: 112

7345 - LV - LCD Projector

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 12

Бренд: Canon Страницы: 18

Бренд: Canon Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды