ACME HYGIEA страница 29 Скачать руководство пользователя | Manualshive

Страница: 29 / 32

background image

19. BaseFan1/2 Too High

Check if the fan is out of order.
Check if the fan circuit on the motherboard breaks down.

The position of each fan of the fixture:

8. Troubleshooting

Following are a few common problems that may occur during operation. Here are some
suggestions for troubleshooting:

A. The unit does not work, no light and the fan does not work
1. Check the connected power.
2. Measure the voltage.
3. Check the power indicator to see whether it can be lit up or not.
B. Not responding to the DMX controller
1. Check whether the DMX connectors and the DMX cables are connected correctly.
2. Check whether the DMX address is correctly set.
3. If the intermittent DMX signal problem occurs, check whether the XLR socket and the signal
cable are well connected.

28A

«
...
27
28
29
30
31
...
»

Содержание HYGIEA

































Отзывы:

Нет отзывов

Похожие инструкции для HYGIEA

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: JB-Lighting Страницы: 40

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: Gardigo Страницы: 24

Бренд: Gardner Bender Страницы: 8

Бренд: Garantia Страницы: 4

Бренд: NARIKA Страницы: 2

Бренд: Macht Dental Страницы: 8

Бренд: MacDon Страницы: 2

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренд: Össur Страницы: 130

Heart Guardian AED

Бренд: Radian Страницы: 36

Бренд: Waves Страницы: 8

Бренд: Feniex Страницы: 5

FOT-930 MaxTester

Бренд: EXFO Страницы: 8

Бренд: GLP Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды