![background image](http://html.mh-extra.com/html/acer/veriton-m4610/veriton-m4610_service-manual_948496101.webp)
93
Chapter 5
SATA1: Serial ATA connectors
These connectors are used to support the Serial ATA devices for the highest datatransfer rates (6.0 Gb/s),
simpler disk drive cabling and easier PC assembly. It doublesthe transfer rate of current SATA 3.0Gb/s
interface.
SATA3~6: Serial ATA connectors
These connectors are used to support the Serial ATA 3Gb/s devices, simpler disk drivecabling and easier PC
assembly. It eliminates limitations of the current Parallel ATAinterface. But maintians register compatibility and
sofeware compatibility with PrallelATA.
F_USB1~4: Front Panel USB 2.0 headers
The motherboard has four USB 2.0 headers supporting four USB 2.0 ports. Addition-ally, some computer
cases have USB ports at the front of the case. If you have thiskind of case, use auxiliary USB connector to
connect the front-mounted ports to themotherboard.
NOTE:
Please make sure that the USB cable has the same pin assignment asindicated above. A different pin
assignment may cause damage or systemhang-up.
Pin
Signal Name
Pin
Signal Name
1
Ground
2
TX+
3 TX-
4 Ground
5 RX-
6 RX+
7 Ground
Pin
Signal Name
Pin
Signal Name
1
Ground
2
TX+
3 TX-
4 Ground
5 RX-
6 RX+
7 Ground
Pin
Signal Name
Function
1
USBPWR
Front Panel USB Power
2
USBPWR
Front Panel USB Power
3
DATA0-
USB Port 0 Negative Signal
4
DATA1-
USB Port 1 Negative Signal
5
DATA0+
USB Port 0 Positive Signal
6
DATA1+
USB Port 1 Positive Signa
7
GND
Ground
8
GND
Ground
9
NC
Not connected
10
USB DET
USB DET
Содержание Veriton M4610
