Acer UM.HV7EE.004 страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 35

background image

EN-3

SCREEN POSITION ADJUSTMENT

In order to optimize the best viewing position, you can adjust the height/tilt
of the monitor.
• Tilt
Please see the illustration below for an example of the tilt range.

5

o

o

«
...
11
12
13
14
15
...
»

Содержание UM.HV7EE.004




































Отзывы:

Нет отзывов

Похожие инструкции для UM.HV7EE.004

Бренд: NCR Страницы: 54

Бренд: M-system Страницы: 8

P401 - MultiSync - 40" LCD Flat Panel...

Бренд: NEC Страницы: 9

LCD3215 - MultiSync - 32" LCD Flat Panel...

Бренд: NEC Страницы: 2

Бренд: Samsung Страницы: 41

13.3 inch HDMI LCD (H)

Бренд: Waveshare Страницы: 12

Бренд: Siko Страницы: 2

Бренд: A&D Страницы: 46

Бренд: Omega Engineering Страницы: 2

LaserLight 2 Series

Бренд: C&S Controls Страницы: 37

Бренд: AOC Страницы: 52

Бренд: AOC Страницы: 1

Бренд: Graco Страницы: 3

Бренд: Crystal Image Technologies Страницы: 28

Бренд: Microlife Страницы: 60

Бренд: Barco Страницы: 54

FFL7165Kl series

Бренд: Mitsubishi Страницы: 14

Бренд: I-Tech Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды