background image

UPGRADING YOUR COMPUTER  - 1

 

UPGRADING YOUR COMPUTER

 

 

Installation precautions 

 

Before  you  install  any  computer  component,  we 

recommend that you read the following sections. 

These 

sections 

contain 

important 

ESD 

precautions along with pre-installation and post-

installation instructions. 
 

ESD precautions 

Electrostatic  discharge  (ESD)  can  damage  your 

processor,  disk  drives,  expansion  boards,  and 

other  components.  Always  observe  the  following 

precautions  before  you  install  a  computer 

component: 
1.

 

Do  not  remove  a  component  from  its 

protective  packaging  until  you  are  ready  to 

install it. 

2.

 

Wear a wrist grounding strap and attach it to 

a metal part of the computer before handling 

components.  If  a  wrist  strap  is  not  available, 

maintain 

contact 

with 

the 

computer 

throughout  any  procedure  requiring  ESD 

protection. 

 

Required tools 

In  performing  the  component  replacement 

process, you will need the following tools: 

• 

Philips screwdriver 

• 

Hex screwdriver 

• 

Flat screwdriver 

• 

Scissors 

 

 

 

Note 
The screws for the different components vary in size. During the disassembly 
process,  group  the  screws  with  their  corresponding  components  to  avoid 
mismatches when putting back the components. 

Содержание Predator Orion 3000


































Отзывы: