1. Product Specification (continued)
1.3.3 User Controls and Indicators
1.3.3.1 Power On / Off Switch
The monitor shall have a power control switch
visible and accessible on the front of the monitor .
The switch shall be marked with icons per IEC 417
, # 5007 and # 5009.The switch shall interrupt the
DC supply to the monitor.
1.3.3.2 Power Indicator LED
The monitor shall make use of an LED type
indicator located on the front of the monitor .
The LED color shall indicate the power states as
given in Table 1.
1.3.3.3 On-Screen Display
The Wistron On Screen Display system shall be
used, controlled by a Menu button. If the buttons
remain untouched for OSD turn off time while
displaying a menu, the firmware shall save the
current adjustments and exit. Also, if the video
controller changes video mode while the OSD is
active, the current settings shall be save
immediately, the OSD turn off, and new video
mode is displayed.
1.3.4 Monitor Modes and Timing Capability
1.3.4.1 Format and Timing
The monitor shall synchronize with any vertical
frequency from 50 to 75 Hz , and with any
horizontal frequency from 31 to 94KHz. If the input
frequency is out of the above – specified range,
the monitor shall display a warning screen
indicating that the input frequency is out of range.
Under no circumstances shall any combination of
input signals cause any damage to the monitor .
1.3.4.2 Factory Assigned Display Modes
There are 13 factory pre-set frequency video
modes. These modes have a factory pre-set
for all characteristics affecting front-of-screen
performance. When the system is powered
on, previously stored screen parameters for a
pre-defined mode will be recalled if the
operating mode is one of those stored in
memory. If the operating mode is not one of
those stored in memory, the monitor CPU will
select the PRESET timing for a mode that is
the next lowest in horizontal scanning
frequency to the mode being currently used.
The screen parameters may be adjusted by
the use of the front bezel controls and then
may be saved as a user defined mode. The
monitor shall include all the preset video
timings shown in the following page.( Please
see Note. (3) )
1.3.4.3 Mode Recognition Pull-in
The monitor shall recognize preset modes
within a range of 1KHz whichever is less for
horizontal ; and within 1Hz for vertical.
1.3.4.4 User Display Modes
In addition to the factory pre-set video modes,
provisions shall be made to store up to 9
user modes. If the current mode is a user
mode, the monitor shall select its previously
stored settings. If the user alters a setting, the
new setting will be stored in the same user
mode. The user modes are not affected by
the pre-set command. If the input signal
requires a new user mode, storage of the new
format is automatically performed during user
adjustment of the display (if required).( Please
see Note.(4) )
Key
When No OSD display
OSD Display
MENU
Menu Display
1.To select the OSD sub-Menu
2.Enter select
>
Speaker Volume/Plus
(with Audio)
1.Right or Down selection of the OSD menu
2.Increase the value after bar selected
<
Speaker Volume/Minus
(with Audio)
1.Left or up selection of the OSD menu
2. Decrease the value after bar selected
Auto
Auto Adjust Function
Menu exit
e
Trigger eColor Management
Trigger eColor Management
Input
Input source select
Input source select
ITEM
Content
Volume
To increase or decrease the sound level
Brightness
Adjust backlight luminance of the LCD panel
Contrast
Adjust gain of R,G,B signal
Clock
Adjust the ratio of dividing frequency of the dot clock
Focus
Adjust the phase of the dot clock
H.Position
The active screen is horizontally move right and left
V.Position
The active screen is vertically move up and down
Color temp
Select three kinds of modes(Warm, Cool, User)
OSD Language
1.USA-select the language among English, French, Italian, Deutsch, Spanish,
,
,
2.EMEA-select the language among English, French,Italian, Deutsch, Spanish, Russian,
Dutch, Finnish
OSD Position
Adjust the OSD menu position
OSD Timeout
The OSD menu show time
Setting
The setting of Input Source, Wide Mode, DDC/CI
Information
It will show resolution, the frequency of horizontal/vertical synchronizing and S/N
Reset
All data copy from shipment factory data
4
Go to cover page
ACER H233H
