Acer e-mill 3VK Скачать руководство пользователя | Manualshive

Страница: 98 / 203

background image

- 9 7 -

quill feed handwheel may be disengaged by moving them outward approximately

1

/

8

”.

NOTE

The feed control lever must be engaged in order to use

manual feed controls. The Quill Feed hand le and Manual

Feed Handwheel may be taken off when not in use.

6-10 Feed Control L ever (#11 on 5HP & #12 on 3HP )

When  this  lever  is  moved  left  it  engages  over -load  clutch  on  pinion  shaft.    Clutch
will  remain  engaged  until  either  quill  stop  comes  in  contact   with  micrometer
adjusting  nut  (forcing  feed  control  lever  to  disengage  automatically),  or  lever  is
released manually by moving it to the left.

NOTE

The Feed Control Lever’s factory default is to disengage

automatically when the quill stop pushes against t he

micrometer adjusting nut or throw adjustment. It may

easily be brought back by regulating the socket set screw

located at the bottom of the tripping rod .

CAUTION

WHEN ADJUSTING THE S OCKET SET SCREW, CHE CK

AUTOMATIC DISENGAGEM ENT IN BOTH

DIRECTIONS: TH AT IS WITH TH E QUILL-STOP NUT

AGAINST THE F EED TRIP LEVER FOR DOWN

POSITION, AND AGAINS T REVERSE T RIP BALL

LEVER FOR THE UP POSITION.

6 -1 1 Q ui ll F e e d H and le ( #1 7 on 5H P & # 19 o n 3 H P )

May be removed by simply pulling handle off! It is recommended that ha ndle be
disengaged when using power feed.

6-12

Qu i ll S t op K nob ( #2 0 on 5 HP & # 11 on 3 H P )

It is used to disengage power feed in either direction as well as acting as a depth
stop when working to a given depth.

6-13 Micrometer Adjusting Nut (#12 on 5HP & #15 on 3HP)

This  nut  is  used  for  setting  depth.    Each  graduation  on  nut  indicates  0.001”
(0.02mm)  and  reads  directly  from  the  scale  mounted  along  its  side.    Depths  may  be
adjusted by setting micrometer nut in conjunction with quill stop.

6 -1 4 Q ui ll L o ck (#1 6 o n 5 H P & # 17 on 3 HP ) :

This is a friction lock to be used when the quill is in a stationary position, such as
for milling. It is recommended this lock be used whenever quill movement is not
desired.

«
...
96
97
98
99
100
...
»

Содержание e-mill 3VK












































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-mill 3VK

Бренд: IBM Страницы: 66

Бренд: Badger Welder Страницы: 6

Бренд: W & H Страницы: 18

BT-CK 18 2B-1.5 Kit

Бренд: Taurus Страницы: 40

Бренд: Placid Industries Страницы: 4

Бренд: Delta Electronics Страницы: 3

Бренд: TDK-Lambda Страницы: 16

Бренд: Magswitch Страницы: 2

Бренд: RODCRAFT Страницы: 36

Бренд: Hama Страницы: 2

Бренд: Laguna Tools Страницы: 9

Бренд: Senco Страницы: 46

Бренд: Hama Страницы: 38

Carlyle Tools 6-711A

Бренд: Napa Страницы: 16

GALAXY EVO EGX850EWT

Бренд: ENERMAX Страницы: 60

Бренд: 2E Страницы: 28

Бренд: BlueSpot Страницы: 6

Бренд: Monzana Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды