background image

- 9 -   

ELECTRICAL REQUIREMENTS 

Standard Test Conditions 

All tests shall be performed under the following conditions, unless otherwise specified. 

Ambient light : 

225 lux 

Viewing distance : 

50 cm in front of LCD panel 

Warrn up time 

All specifications : 

30 minutes 

Fully functional :   

5 seconds 

Measuring Equipment : 

Chroma 2250 signal generator or equivalent, directly   

  

Connected to the monitor under test. 

  

Minolta CA100 photometer, or equivalent 

Control settings 

User brightness control :   

Maximum (unless otherwise specified ) 

User contrast control: 

Typical (unless otherwise specified ) 

User red/white balance,   

Green/white balance and 

Blue/white balance control :

 

In the center (unless otherwise specified ) 

Power input: 

110Vac or 230Vac 

Ambient temperature:

 20 

±

 5 

˚

C ( 68 

±

 9 

˚

 F) 

Analog input mode: 

 

1024 x768 /60 Hz 

 

MEASUREMENT SYSTEMS   

The units of measure stated in this document are listed below:   
1 gamma = 1 nano tesla 
1 tesla = 10,000 gauss 
cm = in x 2.54 
lb = kg x 2.2 
degrees F = [°C x 1.8] + 32 
degrees C = [°F - 32]/1.8 
u' = 4x/(-2x + 12y + 3) 
v' = 9y/(-2x + 12y + 3) 
x = (27u'/4)/[(9u'/2) - 12v' + 9] 
y = (3v')/[(9u'/2) - 12v' + 9] 

nits = cd/(m2) = Ft-L x 3.426 
lux = foot-candle x 10.76 
 

Содержание AL1515






























































Отзывы: