Ace ACE-3105 Скачать руководство пользователя | Manualshive

Страница: 399 / 418

background image

Installation and Operation Manual

Appendix

F Alarm Forwarding

ACE-3105, ACE-3205 Ver. 5.2

1BPSN-to-ATM Alarm Forwarding

F-3

Figure

F-6. PW Link Failure in case of VC Segment Point

Figure

F-7. Physical ETH Failure in case of VP Segment Point

Figure

F-8. Physical ETH Failure in case of VC Segment Point

VCCV-BFD Connectivity Check

The PW link connectivity check and alarm forwarding over a packet-switched
network is performed as follows (see

):

1.

BFD control messages (packets) are generated per PW by both ACE-3105,
ACE-3205 and the remote ACE unit, each towards the PSN direction.

2.

When ACE-3105, ACE-3205 does not receive the BFD control messages from
the remote ACE unit during a number (predefined) of transmission intervals,
it declares that the specific PW is down on its receive (RX) direction.

3.

ACE-3105, ACE-3205 generates 'control-detection-time-expired' packets for
the specific faulty PW towards the remote ACE.

4.

The remote ACE declares a 'neighbor-signal-session-down' state for the PW,
and, when possible, sends corresponding packets under this label.

«
...
397
398
399
400
401
...
»

Содержание ACE-3105



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACE-3105

Бренд: Quintum Страницы: 4

Q gateway 5.5 direct

Бренд: QUNDIS Страницы: 80

Бренд: versa Страницы: 6

Бренд: Digi Страницы: 6

Бренд: Nitgen Страницы: 36

Бренд: Dinstar Страницы: 100

Бренд: Edimax Страницы: 27

Бренд: David Clark Страницы: 11

Бренд: JBM electronics Страницы: 29

WIP310 - iPhone Wireless VoIP Phone

Бренд: Cisco Страницы: 8

WIP310 - iPhone Wireless VoIP Phone

Бренд: Cisco Страницы: 276

Бренд: Vantron Страницы: 15

OfficeConnect 3CR856-95

Бренд: 3Com Страницы: 2

Бренд: More Страницы: 24

HomePortal 3801HGV

Бренд: 2Wire Страницы: 128

Бренд: ZyXEL Communications Страницы: 2

Бренд: Ness Страницы: 7

Бренд: ADT Security Service Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды