Ace ACE-3105 страница 388 Скачать руководство пользователя

Страница: 388 / 418

Appendix

E Encapsulation over PSN

Installation and Operation Manual

E-8

2BEncapsulation over Different PSN Types

ACE-3105, ACE-3205 Ver. 5.2

Parameter Name

Purpose

Type 8100

If VLAN support is enabled, the Ethernet
packet type is set to 0x8100 . 2 bytes long.

VLAN tag

If VLAN support is enabled, this tag includes
the VLAN ID and its priority; configured per
PW. 2 bytes long.

Type 800

IP packet type – 0x800. 2 bytes long.

IP header

The protocol field of the IPv4 header is set
to 17 (UDP). 20 bytes long.

UDP header

8 bytes long; contains the details of:

•

UDP source port – identifies the PW label
of the destination unit

•

UDP destination Port – uses TDMoIP
protocol number: 0x85E (2142)

Control Word

Contains the sequence number and control
bits. 4 bytes long.

Payload

The service data carried on the frame,
depending on the PW type.

PPPoE Packet Format

A PPPoE encapsulation can be either of the following two formats:

Type

8864

PPPoE

header

PPP

header

UDP

header

Control

Word

Payload

Figure

E-10. PPPoE Encapsulation Format – with UDP Header

Type

8864

PPPoE

header

PPP

header

PW label

Control

Word

Payload

Figure

E-11. PPPoE Encapsulation Format –with MPLS in IP

Table

E-9. PPPoE Encapsulation Parameters

Parameter Name

Purpose

Destination MAC address of the access
concentrator which was learned in the
PPPoE session. 6 bytes long.

MAC address of the device. 6 bytes long.

Type 8864

Ethernet packet type is set to 0x8864,
which indicates that it is a PPPoE data
frame. 2 bytes long.

PPPoE header

Contains the PPPoE session ID. 6 bytes long.

Optional

Содержание ACE-3105



































































































































































































































































































































































































































Результаты поиска

Содержание ACE-3105

Отзывы:

Похожие инструкции для ACE-3105

Бренды по названию

Популярные бренды

Ace ACE-3105, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ACE-3105

Отзывы:

Похожие инструкции для ACE-3105

Бренды по названию

Популярные бренды