Ace ACE-3105 страница 131 Скачать руководство пользователя

Страница: 131 / 418

Installation and Operation Manual

Chapter

4 Configuration

ACE-3105, ACE-3205 Ver. 5.2

Configuring for Operation 4-41

Parameter Description

Possible

Values

Default type

The default rate and duplex mode, to be
used if auto-negotiation is disabled.

10BaseT Half Duplex

10BaseT Full Duplex

100BaseT Half Duplex

100BaseT Full Duplex

Default:
100BaseT Full Duplex

Rate limiter

Enable or disable rate limiting on the
displayed Ethernet port.

Enable

Disable

Default: Disable

Output rate
(Mbps)

Set the Mbps rate for the Ethernet port.
Visible only if the Rate limiter option
(see above) is enabled.

1–100

Configuring the E1 Ports

The E1 physical port parameters are configured via the E1 port configuration
menu.

The E1 configuration menu is available if your unit is equipped with E1 ports.

To access the E1 configuration menu:

•

From the Port menu (see

Figure

4-33

), select E1.

The E1 port configuration menu is displayed.

ACE-3205 – RAD Data Communications

Configuration> Physical layer> Port> E1

1. Port number ... (1)

2. Port activation > (Enable)

3. Transmit clock source > (System)

4. RX sensitivity > (Low)

5. Line type > (CRC enabled)

6. Idle code ... (7E)

7. Mode > (E1-UNI)

8. OAM cell generation > (Disable)

9. Failure alarm > (Trunk condition)

10. Trunk condition ... (FF)

Please select item <1 to 10>

ESC-previous menu; !-main menu; &-exit

Figure

4-35. E1 Port Configuration Menu

Note

Содержание ACE-3105



































































































































































































































































































































































































































Результаты поиска

Содержание ACE-3105

Отзывы:

Похожие инструкции для ACE-3105

Бренды по названию

Популярные бренды

Ace ACE-3105, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ACE-3105

Отзывы:

Похожие инструкции для ACE-3105

Бренды по названию

Популярные бренды