Accurate Technology ProPanel Classic Скачать руководство пользователя страница 34

Страница: 34 / 44

P/N 800-1090-104 Rev L102012

Page 34 of 44

The ProPanel Readout Programming Parameters are listed below.
Values in

[ ]

are the range of values available for that Parameter.

Factory Default Value is shown in

Bold

Red.

Parameters that are CUSTOM SET for ProPanel operation are:

Parameter Pr2

has been programmed to

Parameter Pr11

has been programmed to

Parameter Pr13

has been programmed to

Custom value per System

Parameter Pr14

has been programmed to

Parameter Pr30

has been programmed to

Parameter Pr31

has been programmed to

1.000in

Parameter Pr32

has been programmed to

1.500in

Parameter Pr31

has been programmed to

0.750in

Parameters that

DO NOT

apply to ProPanel systems are shown

Grayed Out.

NOTE: Programming parameters are not sequentially numbered due to
firmware differences between systems and provision for future
enhancements / features.

Pr1

– Datum Key

[0 to ± 999.999in] or [0 to ± 9999.99mm]

The value that will be recalled (on the readout) when the

DATUM

key is

pressed. This value would normally be set to 0.00, (Jaws closed) but may be
set to any value the readout is capable of displaying.

Default Value= 0.00

Pr 2

– Direction of Travel

[0 or 1]

This parameter controls the sign of travel (positive vs. negative) when the
measuring system is moved.

FACTORY SET FOR PROPANEL TO 1

Pr3

– Key Lockout

[0 or 1]

This parameter controls the operation of the

and

DATUM

keys.

Default Value = 0

Pr 3 Setting

Key

Action

+, - and Datum keys respond normally

+, - and Datum keys are locked

Содержание ProPanel Classic













































Результаты поиска

Содержание ProPanel Classic

Отзывы:

Похожие инструкции для ProPanel Classic

Бренды по названию

Популярные бренды

Accurate Technology ProPanel Classic, Инструкция по эксплуатации

Результаты поиска

Содержание ProPanel Classic

Отзывы:

Похожие инструкции для ProPanel Classic

Бренды по названию

Популярные бренды