background image

3

General Notes for the operators assigned for installation, maintenance and use

This user’s manual, which represents an integral and essential part of the product, will be delivered by the installer to the user, who has to 
preserve it carefully for further consultation.
This user’s manual must accompany the appliance if the latter gets sold or transferred. 

This appliance has been manufactured to be connected to a water heating system for the heating of the environments 
and for domestic hot water distribution system.
Any other use is considered improper and, therefore, dangerous for people, animals and/or things.

The installation must be made in compliance with the regulations in force and according to the manufacturer's instructions given in this 
manual:
an incorrect installation can cause injury to persons, animals and/or damages to things; the manufacturer declines any liability in such case.

The damages caused by improper installation or use or due to failure to comply with the manufacturer's instructions exclude any liability 
of the latter, be it listed in the contract or not.
Prior to installing the appliance check to make sure its technical data match the requirements for its correct use in the system.

Ensure, as well, that the appliance is intact and has not suffered any damage during transport and handling: do not install damaged and/
or faulty appliances.

Do not obstruct the air suction grids.

For all appliances equipped with options or kits (including electrical ones) use exclusively original accessories.

Do not disperse packagings in the environment after installation: all materials are recyclable and, as a consequence, they must be sent 
to separate wastes collection centres.

Do not leave the packaging at the children's reach; due to their nature they could be source of hazards.

In the event of fault and/or faulty operation of the appliance, shut it off and do not attempt to repair it or to intervene: contact specialised 
and authorized personnel only.
Any repair of the product must be performed using original spare parts

Failure to comply with the indications given above can compromise the safety of the appliance and expose people, animals and/or things 
to danger.

Provide for periodic maintenance of the appliance according to the schedule specified in the appropriate 
section of this manual.
Subjecting the appliance to proper maintenance allows it to work in the best conditions, to protect the envi-
ronment and ensure full safety for people, animals and/or things. 
Incorrect maintenance, both as regards how and when it is performed, can be a source of hazards for per-
sons, animals and/or things.

The manufacturer recommends its clients to have maintenance and repair interventions performed by Authorised Service Centres trained 
to perform the such operations.

In the event of long shut-down periods, disconnect the appliance from the mains and close the gas valve.

Warning: In this case the antifreeze electronic function of the appliance does not work.

If very low temperatures are foreseeable, add antifreeze fluid in the heating system; it is not recommended to empty the plant as it may 
damage the system. To this purpose use specific antifreeze products suitable for heating systems made from several metal types.

As regards the appliances powered by gaseous fuel, if you can smell gas, proceed as follows:
- do not operate electric switches and do not start up electrical appliances;
- do not switch on flames and do not smoke;
- close the main gas supply valve;
- open doors and windows;
- contact a Service Centre, a qualified installer or the gas supplier service centre.
It is strictly forbidden to search for gas leaks using flames.

This appliance has been designed to be installed in the countries of destination specified on the packaging 
label and on the boiler rating plate; installation in countries other than those specified can expose persons, 
animals and/or things to hazards.

The manufacturer declines any liability, be it specified in the sales contract or not, related to failure to comply with the foregoing.

Содержание PLAY ENTRY 20





















































Отзывы: