Access Interfacing Solutions ATR110 Скачать руководство пользователя | Manualshive

Страница: 12 / 70

background image

Page

12

of

70

Copyright © Access-IS 2016

3.6 Barcode module installation

Note:

If you intend to use the Access driver, ensure that you install the driver before you connect

the device to the computer.

3.6.1 Driverless keyboard output

There is no additional driver required for this mode. Connect the USB cable from the ATR110 to a
USB port on the computer.

3.6.2 CDC driver

This method for USB installation uses the Windows CDC drivers.

For this method to operate, you must install the CDC drivers using the file,

AccessISCDC.inf

,

which you can download from

http://www.access-is.com/gettingstarted/

The download (USB Driver for CDC Mode) includes full instructions for use.

Windows assigns a virtual COM port to the ATR110 device. You can find out the COM port number
in Device Manager. You will require the port number to configure the ATR110.

3.6.3 Custom HID

3.6.3.1 HID interface using the Access serial driver (Windows only)

The recommended method for using a USB ATR110 is to configure the device to operate in HID
mode. This allows the device to communicate with the Access driver.

For this method to operate, you must first install the Access driver (ASPS). Download ASPS from

http://www.access-is.com/gettingstarted/

The download (ASPS Software) includes full instructions for use.

Ensure that you install the driver

before

connecting the ATR110 to the host.

3.6.3.2 HID interface without the Access driver

There is no additional driver required for this mode. Connect the USB cable from the ATR110 to a
USB port on the computer.

3.7 NFC module installation

When you connect the ATR110 device to a USB port, Windows automatically detects the NFC
hardware and installs the standard CCID smartcard reader drivers. Some versions of Windows may
prompt you to search automatically for a driver.

The NFC module also exposes a HID interface for configuration and control. Refer to

management interface commands

on page 50 for the command set and its responses.

In Device Manager, the smartcard reader and HID-compliant device represent the NFC module.

«
...
10
11
12
13
14
...
»

Содержание ATR110







































































Отзывы:

Нет отзывов

Похожие инструкции для ATR110

HID iCLASS RWK400

Бренд: Assa Abloy Страницы: 12

Бренд: ICT Страницы: 38

Бренд: IDEC Страницы: 39

Бренд: Cognex Страницы: 16

PRS-505/LC - Portable Reader System

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

PRS-350SC - Reader Pocket Edition&trade

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

PRS-300BC - Reader Pocket Edition

Бренд: Sony Страницы: 2

PRS-300 - Reader Pocket Edition&trade

Бренд: Sony Страницы: 2

PRS-300 - Reader Pocket Edition PRS-300LC - Reader Pocket Edition PRS-300

Бренд: Sony Страницы: 2

PRS-600 - Electronic Book Reader

Бренд: Sony Страницы: 14

PRS-350 - Reader Pocket Edition&trade

Бренд: Sony Страницы: 16

PRS-300 User’s Guide

Бренд: Sony Страницы: 14

Бренд: Sony Страницы: 60

Бренд: Sony Страницы: 82

Бренд: Sony Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды