READ ME FIRST – SETUP INSTRUCTIONS
Thank you for purchasing the Accell UltraAV HDMI Distribution
Amplifi
er. This product is designed to provide an exceptional
performance and value. Please review the manual before
operating and retain for future reference.
- CAUTION -
1. Ensure the matrix and receivers
have suffi
cient ventilation. Do not
cover ventilation openings. Do not
install in a confi
ned space.
2. Do not operate near source
of heat. Do not stack on top,
underneath or between other heat
generating unit/s including other
amplifi
ers.
3. Unplug power adapter if not
used for an extended period.
4. To prevent damage from power
surges, the unit should be plugged
into a surge protector or surge pro-
tected power source.
5. Do not use near liquid or areas
of heavy moisture.
6. Clean unit with a clean and dry
cloth only.
7. This unit cannot be serviced in
the
fi
eld. Contact Accell if service is
required.
8. Do not open case, risk of shock -
shock hazard.
9. Do not modify power cord or use
the product if the power cord is
damaged.
Introduction
The UltraAV HDMI 4x4 Matrix and Distribution Amplifier featuring
HDBaseT accepts signals from up to 4 HDMI enabled audio/video sources
and distributes the signal to up to 4 HDMI enabled displays. The matrix
can be configured to send any input to any HDMI displays, monitors,
projectors or TV’s.
Over-Current and Over-Voltage Protection
The circuit boards are equipped with both over-current and over-voltage
protection and will automatically power down if encountered. The circuit
boards will restore automatically once the excessive current or voltage
has passed.
Package Contents
●HDMI Distribution Amplifier (Matrix) ●1 Power Adapter (for Matrix)
●4 HDBase
T Receivers
●4
Po
wer Adapters (for
Re
ceivers)
●CD-ROM (for RS-232 control)
●4-P
air IR-TX and IR-RX
●Remote Control (with battery)
●Owne
r’s Manual
●2 Front Panel Mounting Ears (with 4 Screws)
Model Number:
K072C-014B
UltraAV
®
HDMI 4x4 Matrix
with HDBaseT
Setup
Note: All Cat5e/6 cables must be terminated to 568B standards.
Unsheilded (or properly terminated sheilded cable), solid core Cat5e,
Cat6, Cat6e, Cat7 or Cat7e cable can be used. Str
anded core is not
suggested as it can reduce signal transfer. Recommended to use a
continuous length of cable terminated at the matrix and receiver ends.
With the matrix power switch in the OFF position, connect an HDMI High
Speed cable from the HDMI Output of the most commonly used audio/
video source to the HDMI Input 1 located on the rear of the matrix.
Similarly
, connect the remaining source devices to the HDMI Input Ports
on the matrix.
Tips: Use the shortest length HDMI cables possible in each point
in the installation. Use only High Quality and High Speed HDMI
cables.
If desired, run a LAN cable from your network or router into the port
labeled LAN IN on the rear of the matrix.
Next, connect a Cat5e/6 cable to the HDBase
T Out 1 port on the rear of
the matrix. Connect the other end of the Cat5e/6 cable to the HDBaseT
IN port on the rear of the HDBaseT receiver positioned near the TV. Run
a short, High Speed HDMI cable from the HDMI Out port on the receiv
er
to the HDMI In port on the TV. If desired, two Ethernet ports are
provided on the rear of the receiver for connection to Internet enabled
TV and/or computer. Plug a provided power adapter into an AC outlet
and the other end into the HDBaseT receiver. Using the same steps,
connect the remaining audio/video sources to the matrix.
The matrix has internal memory that stores the system
information for faster switching. Please follow the steps in the
order listed:
T
urn ON the displays and ensure they are awake (not in
standby mode). Check the displa
ys INPUT setting to ensure the correct
HDMI port is active.
T
urn on the source devices and ensure they are awake (not in standby
mode). Connect the power adapter to the matrix. Plug the power
adapter into a surge protected AC power outlet. Turn the matrix power
switch to the ON position.
The matrix has a low power draw and is intended to be left on. If
the matrix is turned off, start up the system as noted above. If new
hardw
are is added, please perform a RESET
.
To
RESET the matrix, turn off the display and source devices.
Power off
the matrix and unplug the power adapter from the rear of the matrix.
Wait 20 minutes for the memory of the system configuration inside of
the matrix to be deleted.
Fo
llow the setup instructions above to correctly
initiate the setup.
HDMI 4x4 Matrix and Distribution Amplifier
Model: K072C-014B
Speci
fi
cations
● Independently access 4 HDMI Sources from 4 HDMI Displ
ays
● Supports HD resolutions up to 1080P and 3D
● HDMI 1.4a, HDCP 1.2 compliant
● Audio formats supported:
DT
S-HD 7.1, Dolby T
rue-HD 7.1
● Deep color up to 36-bi
t
● RS232 P
ort for control
● Maximum HDMI input/output cable length: Up to 16ft./5m
● Maximum Cat5e/6 output cable length: Up to 328ft./100m
● Supports up to 100 Base
T Ethernet, two ports per receiver
● 19” Rack Mounting (front panel mounting br
ack
ets included)
● 12V DC, UL Listed Power Supply for 4 x 4 Matrix Uni
t
● 5V DC, UL Listed Power Supplies for Receiver Units (4
To
tal)
● Matrix dimensions: 17.3”W x 2”H x 7.9”D (440W x 51H x 20D mm)
● Receiver dimensions: 4.4” W x .9” H x 3” D (112W x 23H x 76D mm)
● Oper
ating temperature r
ange: 5 to 131°F (-15 to 55°C)
● Oper
ating humidity r
ange: 5% to 90% RH (no condensation)
